JVC DR-DX5SEK Instructions Manual

Also see for DR-DX5SEK: Instructions Service manual

Contents

70 EN SYSTEM CONNECTIONSConnect the satellite receiver to the [L-2 IN/DECODER] connector,then connect the [L-1 IN/OUT] connector to the TV’s connector.NOTES:● Set AL-2 SELECTB to AVIDEOB or AS-VIDEOB. (A pg. 64)● You can use the Automatic Satellite Programme Recordingfunction (A pg. 50) with this connection. (HDD deck only)● To record a programme via the satellite receiver, select L-2 modeby pressing PR +/– so that AL-2B appears on the front displaypanel.● For details, refer to the instruction manual of the satellite receiver.These instructions enable you to connect your unit to a DolbyDigital Decoder or an amplifier with built-in DTS.1 Connect the unit and a Dolby Digital Decoder or an amplifierwith built-in DTS using either an optional optical cable or anoptional coaxial cable.NOTES:● For Dolby Digital sound, set ADIGITAL AUDIO OUTB to ADOLBYDIGITAL/PCMB. (A pg. 71)● For DTS sound, set ADIGITAL AUDIO OUTB to ASTREAM/PCMB.(A pg. 71)CAUTIONS:● This unit has a dynamic range of more than 110 dB with regardsto its Hi-Fi audio capability. It is recommended that you check themaximum level if you are going to listen to the Hi-Fi audio signalsthrough a stereo amplifier. A sudden surge in the input level tothe speakers may damage them.● Some speakers and televisions are specially shielded to preventtelevision interference. If both are of the non-shielded type, do notplace the speakers adjacent to the TV set as this can adverselyaffect the playback picture.When you can’t switch the audio channel of a bilingualprogrammeWhen the unit is connected with a digital audio device using anoptional optical cable and ADIGITAL AUDIO OUTB is set toADOLBY DIGITAL/PCMB, it is not possible to switch the audiochannel of a bilingual programme recorded on a DVD-RAM orDVD-RW (VR mode) disc. In this case, perform the following stepsusing the remote control to switch ADIGITAL AUDIO OUTB fromADOLBY DIGITAL/PCMB to APCM ONLYB.A Press SET UP to access the Main Menu screen.B Press selection keys to select ADVD VIDEO SET UPB, then press G.C Press selection keys to select AAUDIO OUTPUTB, then press G.D Press selection keys to select ADIGITAL AUDIO OUTB, thenpress ENTER.E Press selection keys to select APCM ONLYB, then pressENTER. (A pg. 71)F Press SET UP to complete the setting.G Press AUDIO to select the desired audio channel.Connecting To A Satellite ReceiverIMPORTANTWhen you set AL-2 SELECTB to ASAT VIDEOB or ASATS-VIDEOB (A pg. 64), it is possible to view a satellite broadcastwith the TV set to its AV mode even if the unit is turned off. Whenthe unit is in Stop mode or recording, press TV AV/VIDEO on theremote control to turn off the VIDEO indicator on the frontdisplay panel.● If you turn on the unit when the satellite receiver’s power is off,nothing appears on the TV screen. In this case, turn on thesatellite receiver, or set the TV to its TV mode, or press TV AV/VIDEO on the remote control to set the unit to the AV mode.Outdoor unitSatellite cableSatellite receiverAerialTV aerial cableANTENNA OUTANTENNA INTVConnecting To A Dolby Digital DecoderOr An Amplifier With Built-in DTSDolby Digital Decoder oramplifier with built-in DTSCoaxial cable(not supplied)Rear of unitNote for connection:Remove the protection cap from the optical cable.To [DIGITAL AUDIOOUT (COAXIAL)]To DIGITAL AUDIO inputOptical cable(not supplied)To [DIGITAL AUDIOOUT (OPTICAL)]