JVC 1105RYMMDWJEIN Instructions Manual

Contents

20* When “TV” is selected as the source, only “DIGITAL” or“ANALOGUE” appears on the display as the audio inputsetting.NOTES• “HDMI” is available only for the source with “HDMI” selected inthe video input setting (see the left column).• “DIGITAL” is available for the source assigned for “DIGITAL IN1,” “DIGITAL IN 2,” or “DIGITAL IN 3.” See page 25 for details.Initial setting of VIDEO INPUT and AUDIO INPUT foreach sourceDVR/DVD HDMI HDMIVCR S ANALOGVIDEO HDMI HDMITV DIGITALUSB WIRELESS DIGITAL (fixed)USB TERMINAL DIGITAL (fixed)FM ANALOG (fixed)AM ANALOG (fixed)AUX S DIGITAL3 Adjust the volumeTo increase the volume, turn MASTER VOLUMEcontrol clockwise (or press VOLUME + on theremote control).To decrease the volume, turn MASTER VOLUMEcontrol counterclockwise (or press VOLUME – onthe remote control).• When you adjust the volume, the volume level indicationappears on the display for a while.CAUTION:Always set the volume to the minimum before starting anysources. If the volume is set at its high level, the sudden blast ofsound energy can permanently damage your hearing and/or ruinyour speakers.NOTEThe volume level can be adjusted within the range of “0” (minimum)to “50” (maximum).Selecting the video input settingSelect the proper video input setting according to the connectionmethod on pages 10 to 15.From the remote control ONLY:Press VIDEO INPUT to select the video inputsetting.• Each time you press the button, the input setting changes asfollows. This setting is memorized for each source.NOTES• When “DVR/DVD” or “VCR” is selected as the source and“VIDEO OUTPUT” (see page 33) is set to “RGB/C,” the videoinput setting changes between “RGB,” “S,” and “C.”• For “VCR” and “VIDEO,” you can select “HDMI” and “CMPNT”for the source you assigned in “HDMI SELECT” and “CMPNTSELECT” (see page 32).• When the video input setting and the audio input setting areboth set to “HDMI,” changing the video input setting changes theaudio input setting to the appropriate setting.Selecting the audio input settingSelect the proper audio input setting according to the connectionmethod (analogue or digital) on pages 10 to 16.• In case of digital connection using the terminals on the rear ofthe receiver, you also need to select the correct digital inputterminal. (See “Setting the digital input (DIGITAL IN) terminals—DIGITAL IN 1/2/3” on page 31.)From the remote control ONLY:Press AUDIO INPUT to select the audio inputsetting.• Each time you press the button, the audio input setting changesas follows. This setting is memorized for each source.HDMI (for “DVR/DVD,” “VIDEO” and “VCR”):Select for the source with HDMI connection. Thereceiver automatically detects the incomingsignal format, then the digital signal formatindicator (LINEAR PCM, , , or96/24) for the detected signal lights up,and the HDMI lamp on the front panel lights up.DIGITAL*: Select for the digital input setting. The receiverautomatically detects the incoming signalformat, then the digital signal format indicator(LINEAR PCM, , , or 96/24)for the detected signal lights up.ANALOG*: Select for the analogue input setting. The(ANALOGUE) ANALOG indicator lights up on the display.A MULTI (Only for “DVR/DVD”):Select when connecting a DVD recorder or DVDplayer to DVD MULTI IN jacks (see page 12).The ANALOG indicator lights up on the display.LS.WFRRAUTO SURRANALOGLLS RSS.WFR LFEC RAUTO SURRDIGITALDIGITALHDMI CMPNT (component)(Back to the beginning)S (S-video) C (composite)LLS RSS.WFR LFEC RAUTO SURRDIGITALDIGITALHDMI DIGITALA MULTI (Back to the beginning)ANALOGSourceSetting VIDEO INPUT AUDIO INPUT