JVC 0710DTSMDTJEIN Instructions & Installation Manual

Contents

1 – ENKD-S27CD RECEIVER : INSTRUCTIONS/INSTALLATION0710DTSMDTJEINEN© 2010 Victor Company of Japan, LimitedGET0698-001A[J]1 Turn on the power.23Canceling the display demonstration4 Select <DEMO OFF>.56 Finish the procedure.Setting the clock1 Turn on the power.23 Select <CLOCK>.4 Select <CLOCK SET>.5 Adjust the hour.6 Adjust the minute.7 Finish the procedure.PreparationsFor safety...• Do not raise the volume level too much, as this willblock outside sounds, making driving dangerous.• Stop the car before performing any complicatedoperations.Temperature inside the car...If you have parked the car for a long time in hot orcold weather, wait until the temperature in the carbecomes normal before operating the unit.Basic operationsWhen you press or hold the following button(s)...Main unit Remotecontroller General operationsTurns on.• When the power is on, pressing /I/ATT on the remote controlleralso attenuates the sound or pauses. Press /I/ATT again to cancelmuting or resume playback.Turns off if pressed and held.Selects the available sources (if the power is turned on).• If the source is ready, playback also starts.Adjusts the volume level.— Selects items.—• Mutes the sound while listening to a source. If the source is “CD” or“USB,” playback pauses. Press the control dial again to cancel mutingor resume playback.• Confirms selection.Selects the sound mode.• Enters tone level adjustment directly (see page 3) if pressed and heldEQ BASS-TRE on the main unit.— Enters playback mode menu directly (see page 2).— Power off : Checks the current clock time.Power on : Changes the display information.[European Union only]Warning:If you need to operate the unit while driving, be sureto look around carefully or you may be involved in atraffic accident.(Initial setting)[Hold](Initial setting)[Hold]Control dial Loading slot Display windowAuxiliary input jackEjects the discDetaches the panelUSB (Universal SerialBus) input jackINFORMATION (For U.S.A.)This equipment has been tested and found to comply with the limits for a Class B digital device, pursuantto Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmfulinterference in a residential installation. This equipment generates, uses, and can radiate radio frequencyenergy and, if not installed and used in accordance with the instructions, may cause harmful interferenceto radio communications. However, there is no guarantee that interference will not occur in a particularinstallation. If this equipment does cause harmful interference to radio or television reception, which can bedetermined by turning the equipment off and on, the user is encouraged to try to correct the interference byone or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.Caution:Changes or modifications not approved by JVC could void the user’s authority to operate the equipment.IMPORTANT FOR LASER PRODUCTS1. CLASS 1 LASER PRODUCT2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave allservicing to qualified service personnel.3. CAUTION: (For U.S.A.) Visible and/or invisible class II laser radiation when open. Do not stare into beam.(For Canada) Visible and/or invisible class 1M laser radiation when open. Do not view directlywith optical instruments.4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.Thank you for purchasing a JVC product.Please read all instructions carefully before operation, toensure your complete understanding and to obtain the bestpossible performance from the unit.For customer Use:Enter below the Model No. and Serial No. which are locatedon the top or bottom of the cabinet. Retain this informationfor future reference.Model No.Serial No.Remote sensor• DO NOT expose to bright sunlight.Returns to the previous menuHow to attach/detach the controlpanelHow to reset your unitReset the unit after installation iscompleted.• Your preset adjustments willalso be erased.How to forcibly eject a disc• You can forcibly eject the loaded disc even if thedisc is locked. To lock/unlock the disc, see page 2.• Be careful not to drop the disc when it ejects.• If this does not work, reset your unit.Preparing the remote controller(RM-RK50)When you use the remote controller for the first time,pull out the insulation sheet.If the effectiveness of the remote controllerdecreases, replace the battery.Replacing the lithium coin batteryFor USA-California Only:This product contains a CR Coin Cell Lithium Batterywhich contains Perchlorate Material—specialhandling may apply.See www.dtsc.ca.gov/hazardouswaste/perchlorateCaution:• Danger of explosion if battery is incorrectlyreplaced. Replace only with the same or equivalenttype.• Battery shall not be exposed to excessive heat suchas sunshine, fire, or the like.Warning (about battery handling)To prevent accidents and damage:• Do not install any battery other than CR2025 or itsequivalent.• Store out of reach of children.• Do not recharge, short, or dismantle.• Do not dispose of in fire.• Do not carry around with other metallic materials.• Wrap the battery with tape and insulate whenthrowing away or saving it.[Hold]Insulation sheetCR2025