I-Inc iH182APB User Manual

Contents

I-Inc iH182APB User Manual Manual pdf 19 page image

User’s ManualERROR MESSAGE & POSSIBLE SOLUTIONS CABLE NOT CONNECTED :1. Check that the signal-cable is properly connected, If the connector is loose, tighten theconnector’s screws.2. Check the signal-cable’s connection pins for damage. INPUT NOT SUPPORT :Your computer has been set to unsuitable display mode, set the computer to display mode givenin the following table.FACTORY PRESET TIMING TABLE:MODE RESOLUTION HORIZONTALFREQUENCY(KHz)VERTICALFREQUENCY(Hz)iH182 iH192 iH202 iH222 iH2321 640×350 @70Hz 31.469 70.087 ▲ ▲ ▲ ▲ ▲2 640×400 @56Hz 24.827 56.424 ▲ ▲ ▲ ▲ ▲3 640×400@70Hz 31.469 70.087 ▲ ▲ ▲ ▲ ▲4 640×480 @60Hz 31.469 59.94 ▲ ▲ ▲ ▲ ▲5 640×480 @67Hz 35 66.667 ▲ ▲ ▲ ▲ ▲6 640×480 @70Hz 36.052 70.004 ▲ ▲ ▲ ▲ ▲7 640×480 @72Hz 37.861 72.809 ▲ ▲ ▲ ▲ ▲8 640×480 @75Hz 37.5 75 ▲ ▲ ▲ ▲ ▲9 720×400@70Hz 31.469 70.087 ▲ ▲ ▲ ▲ ▲10 720x480@60Hz 31.469 59.94 ▲ ▲ ▲ ▲ ▲11 800×600 @56Hz 35.156 56.25 ▲ ▲ ▲ ▲ ▲12 800×600 @60Hz 37.879 60.317 ▲ ▲ ▲ ▲ ▲13 800×600 @72Hz 48.077 72.188 ▲ ▲ ▲ ▲ ▲14 800×600 @75Hz 46.875 75 ▲ ▲ ▲ ▲ ▲15 832×624 @74.6Hz 49.725 74.5 ▲ ▲ ▲ ▲ ▲16 1024×768 @60Hz 48.363 60.004 ▲ ▲ ▲ ▲ ▲17 1024×768 @66Hz 53.964 66.132 ▲ ▲ ▲ ▲ ▲18 1024×768 @70Hz 56.476 70.069 ▲ ▲ ▲ ▲ ▲19 1024×768 @75Hz 60.023 75.029 ▲ ▲ ▲ ▲ ▲20 1024×768 @75Hz 60.15 74.72 ▲ ▲ ▲ ▲ ▲21 1152×864 @75Hz 67.5 75 ▲ ▲ ▲ ▲ ▲22 1152×900 @66Hz 61.846 66.004 ▲ ▲ ▲ ▲ ▲23 1280×720 @60Hz 45 60 ▲ ▲ ▲ ▲ ▲24 1280×768 @60Hz 47.776 59.87 ▲ ▲ ▲ ▲ ▲25 1280×768 @75Hz 60.289 74.893 ▲ ▲ ▲ ▲ ▲26 1280×960 @60Hz 60 60 ▲ ▲ ▲ ▲ ▲27 1280×960 @75Hz 74.592 74.443 ▲ ▲ ▲ ▲ ▲28 1280×1024 @72Hz 76.02 71.448 ▲ ▲ ▲29 1360×768 @60Hz 47.712 60.015 ▲ ▲ ▲ ▲ ▲19