Menu
Husqvarna X-SYNC HP500BT-01 Operator's Manual
Also see for HP500BT-01: Operator's manualOperator's manual
                                                                                                                                                                                                                                        |
• Do not push the earmuffs against the helmet shell. Ifyou do that, it can cause cracks around the side ofthe helmet.(Fig. 4)• Do not put the product in storage at temperaturesabove +55°C/+131°F, for example on a dashboard.Do not put the product in storage at temperaturesbelow -20°C/-4°F.• The wearer should ensure that the ear-muffs arefitted, adjusted and maintained in accordance withthis operator's manual.• The ear-muff is provided with safety-related audioinput. The user should check correct operationbefore use. If distortion or failure is detected, theuser should refer to the manufacturer’s advice formaintenance.Battery safety• The earmuff is provided with level-dependentattenuation. The user should check for correctoperation before use. If a malfunction or fault isdetected, the user should follow the manufacturer'sinstructions for maintenance.• The product contains battery and electricalcomponents that may cause ignition in flammable orexplosive atmospheres. Do not use in environmentswhere sparks may cause a fire or explosion.• Only charge the product within temperature range0°C to +40°C/+32°F to +104°F. Charging outsidetemperature range can damage the electronics andbattery.AssemblyIntroductionWARNING: Move your hair to the sidebefore you assemble the product. Makesure that the sealing rings are tight againstyour head and around your ears before youoperate the product.To put on the earmuffs with headband1. Put the headband across the top of your head.2. Move the earmuffs up or down to adjust the height.(Fig. 5)To assemble the earmuffs to a helmet1. Assemble the correct adapter attachment type to thehelmet shell. Refer toApproved helmets on page11.2. Assemble the helmet fork on the attachmentadapter. (Fig. 6)Note: Refer toApproved helmets on page 11 formore information about which helmet attachment isapplicable to your helmet.3. Move the earmuffs to the lowest position.4. Lift the earmuffs out and up until they lock in standbyposition. (Fig. 7)5. Do a mark on the cable.a) For helmet H300, do a mark 27 cm/11 in (X) fromeach earmuff.b) For helmet Spire Vent X, do a mark 14.5 cm/6 in(Y) from each earmuff. (Fig. 8)6. Put the helmet attachment in the slot on the helmet.(Fig. 9)7. Continue to assembly instructions for your approvedhelmet.CAUTION: Make sure that the cable isnot twisted or has a small bend radius. Makesure that the cable can move smoothly intothe opening of the helmet.To assemble the earmuffs to the helmet H3001. Release the head harness from the helmet. (Fig. 10)2. Attach the cable to the holes with the cable ties orclips. (Fig. 11)3. If you attach the cable with cable ties, cut the cabletie and push the cable tie lock into the side slot.4. Make a loop of the cable and attach the headharness and neck protection. Make sure that thecable is between the helmet shell and the headharness. (Fig. 12)To assemble the earmuffs to the helmet SpireVent X1. Put the cable in a loop rearward.2. Attach the cable to the head harness with cable ties.Attach the cable tie through the backstrap of theheadband.3. Cut the cable tie.4. Put the remaining part of the cable in a looprearward, behind the rear headband. (Fig. 13)To put the earmuffs in operation position1. Put the helmet on your head.2. Adjust the earmuffs until they are tight around yourears and tight against your head. (Fig. 14)To put the earmuffs in standby position• Lift the earmuffs out and up until they lock in standbyposition. (Fig. 15)8 2146 - 004 - 18.12.2023 |
Related manuals for Husqvarna HP500BT-01
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved