Harman AMX MXT-1001 Quick Start Manual

Also see for AMX Modero X Series: Quick start guide Quick start guide Quick start guide Instruction manual Quick start guide

Harman AMX MXT-1001 Quick Start Manual Manual pdf 1 page image

QUICK START GUIDEMXT-1001 10.1" Modero X® Series G5 Tabletop Touch PanelOverviewThe MXT-1001 10.1" Modero X Series® G5 Tabletop Touch Panel (FG5968-47)features the G5 Graphic Engine to provide fast and smooth animations andtransitions, as well as a Quad Core Processor.The MXT-1001 features edge-to-edge capacitive touch glass with multi-touchcapabilities. It features advanced technology empowering users to operate AVequipment seamlessly, while providing the ultimate in audio and video quality.The distinctive appearance will complement even the most sophisticated meetingfacilities and homes.Product Specif icationsConnector LocationsUSB peripherals (mouse, keyboard, etc.) may be connected to either of the twoUSB ports on the rear of the device. Updates to the device’s firmware can alsomade via the USB ports (FIG. 2).Power via PoEPower for the MXT-1001 is supplied via PoE (Power Over Ethernet), utilizing anAMX-certified, capacitive touch-compliant PoE injector such as the PS-POE-ATHigh Power PoE Injector (FG423-81) or other approved AMX PoE power sourceConnect the incoming Ethernet cable to the RJ45 port on the cable attached tothe device.Ethernet Cable Installation and Modif icationIn installations where you wish to conceal the Ethernet cable, a hole at least 1.00”(2.54 cm) in diameter is required in the surface to allow passage of the femaleRJ45 connector (FIG. 3).If using a smaller hole is unavoidable, you will need to disconnect the Ethernetcable (ECA5968-05) from the device, to feed the male end of the cable through.Note: The minimum diameter hole through which the Ethernet cable may pass is0.50" (1.27 cm).To disconnect and reconnect the MXT-1001’s Ethernet cable:1. On a soft surface, turn the MXT-1001 face-down to access the bottom of thedevice.2. Remove the clamp holding the Ethernet cable (FIG. 3).3. Remove the Ethernet cable connector and pull the cable out of the clamp.4. Pass the Ethernet cable (ECA5968-05) through the hole, with the RJ45connector on the other side of the installation surface from the device.5. Press the Ethernet cable back into the clamp.Do NOT tighten the clamp at this time.6. Using a non-conductive item such as a wooden stick, reinsert the Ethernetcable connector into the device. Ensure that the connector is properlyseated.7. Tighten the clamp to secure the Ethernet cable.Make sure the clamp is around the bundled black cable, not the individualwires.8. Connect the RJ45 connector to its incoming Ethernet cable and apply power.FIG. 1 MXT-1001MXT-1001 SPECIF ICATIONSDimensions (HWD) 6 7/8" x 9 7/8" x 4 7/8" (174 mm x 252 mm x 124 mm)Weight 3.1 lbs (1.41 Kg)PowerConsumption• Full-On: 12.95 W maximum• Standby: 5.8 W• Shutdown: 1 W• Start-Up Inrush Current: Not applicable due to PoEstandardExternal PowerSupply RequiredOptimal performance requires use of one of the followingAMX PoE power supplies (not included):• PS-POE-AF-TC, PoE Injector, 802.3AF Compliant(FG423-83)• NXA-ENET8-2POE, Gigabit PoE Ethernet Switch(FG2178-63)Certifications • UL 60950-1• FCC Part 15 Class B• C-Tick CISPR 22 Class B• CE EN 55022 Class B and EN 55024• CB Scheme IEC 60950-1• IC• IEC/EN-60950• RoHS/WEEE compliantEnvironmental • Temperature (Operating): 32° F to 104° F (0° C to 40° C)• Temperature (Storage): 4° F to 140° F (-20° C to 60° C)• Humidity (Operating): 20% to 85% RH• Humidity (Storage): 5% to 85% RH• Power ("Heat") Dissipation:On: 44.2 BTU/hrStandby: 19.8 BTU/hrIncludedAccessories• MXA-USB-C, USB Port Cover Kit (FG5968-18)• 3/4" Mini-Grommet (FG570-01)• MXA-CLK, Modero X/S Series Cleaning Kit (FG5968-16)Sleep ButtonNFC SensorUSB Ports (2)Sleep ButtonFIG. 2 MXT-1001 - REAR VIEWFIG. 3 BOTTOM OF THE MXT-1001USB Ports Entry for RJ45/PoE CableSpeakerSleep buttonEthernet Cable ConnectorClamp

/ 2

Related manuals for Harman AMX Modero X Series