Harken WINGMAN MH Product Manual

Harken WINGMAN MH Product Manual Manual pdf 1 page image

PRODUCT MANUALPart Number: IN172.3mWINGMAN MH(Material Handling)MANUFACTURER:262-691-3320harken.cominfoUSA@harkenindustrial.comHarken, Inc.N15W24983 Bluemound Rd.Pewaukee, WI, 53072USAWORKING LOAD LIMIT: 675 LBSROPE DIAMETER: 8 MM FIBER [5/16"](replace rope only with Harken authorized replacement rope)Please read these instructions carefullybefore installing, servicing, or operatingthe equipment. This manual may bemodified without notice. In the event thismanual is translated, the English versionis definitive. For the latest manualrevision, go to www.harken.com, clickSafety & Rescue, then product support.WARNING!ACTIVITIES INVOLVING THE USE OF THIS EQUIPMENT AREINHERENTLY DANGEROUS. YOU ARE RESPONSIBLE FORYOUR OWN ACTIONS AND DECISIONS.THIS DEVICE IS NOT INTENDED FOR HUMAN SUSPENSION.BEFORE USING THIS EQUIPMENT, YOU MUST: Read and understand all instructions for use Get specific training in the Wingman MH proper use Become acquainted with its capabilities and limitations Understand and accept the risks involvedFAILURE TO HEED ANY OF THESE WARNINGS MAY RESULTIN SEVERE INJURY OR DEATH1. USE- The Wingman MH is a mechanical-advantage device for load lifting and releasing.- This product is intended to be used by competent persons familiar with the use ofpulleys for lifting.- Use only with supplied rope.- To prolong the life of this product, care in use is necessary. Avoid rubbing againstabrasive surfaces and sharp edges.- The Wingman MH is not certified for fall arrest, suspension, or positioning of ahuman. Use only for moving non-human loads.2. COMPATIBILITY- Always verify the Wingman MH is compatible with the other components of yoursystem.- Any equipment used with the pulleys (such as anchors and locking connectors)must conform to applicable standards and/or regulations.3. SAFETY- In the event that the Wingman MH is shock-loaded, it must be removed fromservice and destroyed.4. INSPECTION- Verify all pieces of equipment in the system are in good working condition and theproduct is correctly positioned while in use. Check the condition of the productbefore and after each use. Remove from service if there is any doubt about safetyand serviceability.- Visually and by touch, inspect pulley for cracks, distortion, corrosion, scratches,gouges, sharp edges, or rough areas that might abrade a rope, or alter the normalrotation of the sheave(s) or the normal action of the release handle.- Verify the sheaves turn freely.- Verify all markings and labels are present and legible.- An in-depth inspection must be carried out at least every 12 months and morefrequently if the pulley is in frequent and intense use.5. OPERATION- Function test - Before each use, verify the device is working properly. Connect oneend of the Wingman MH to an anchor with a shackle, apply a load to the other end,and verify the rope is locked at the cam block. Grip the haul/tail end of the rope withone hand and gently open the release handle with the other hand, allowing the ropeto pass through the cam block and lower the load. Gradually close the release handleand verify the rope is locked by the cam block. With a moderate load on the system,WARNING!DO NOT EXCEED RECOMMENDED WORKING LOAD.AVOID SHOCK LOADING.open the release handle and release it. Verify the release handle snaps closed. Pullon the haul/tail end of the rope and verify the sheaves turn freely and you hear aclicking sound.- Lowering - To lower a load, carefully open the release handle while securelytailing the haul/tail end of the rope. Control the speed of descent by acombination of modulating the release handle and hand grip on the rope. To stoplowering, gradually close the release handle until the cam block locks the rope.Releasing the handle completely will immediately stop the lowering action.- Remote Release - To use the remote release, tie a stopper knot in the end of theremote release cord. Thread the other end through the hole in the release handle.Connect the Wingman MH to an anchor using a shackle, then connect the other endto the load. Thread the remote release cord through the upper shackle. While firmlygripping the haul/tail end of the rope, pull on the remote release cord to actuate therelease handle. Using both hands on the rope while simultaneously actuating therelease handle, gradually relax your grip on the rope so that it begins to slide throughyour hands. Modulate the descent speed of the load by a combination of adjustingyour grip on the rope and moving the remote release cord up or down.NOTE: Keeping the same hand on both the rope and the cord ensures that if yourhand travels closer to the anchor point the remote release eases and the loweringstops.Hold the remote release handle and haul/tail end of the rope together to control therate of descent. To stop lowering, ease pressure on the handle to close and lock it.Releasing the handle completely immediately stops the lowering action. Limit the loadto 300 lbs when using remote release.EXAMPLE:Release HandleShackleRed BlockCam (or Silver) BlockRopeRemoteReleaseCordFOR PROTOTYPING PURPOSES ONLYTION PURPOSES ONLYSURFACE FINISH:MATERIAL:DRAWING NUMBER REV.FINISH:PART #MFG. APR :DRAWN BY :TOLERANCES UNLESS OTHERWISE SPECIFIED:DECIMAL:ANGULAR:SCALE:ENG. APR :Road3072 © The designs, constructions, arrangements, disclosures and devicesillustrated in presentations bearing this note are the property of Harken, Inc,Pewaukee, WI and are submitted in confidence with the understandingthat such material shall not be utilized in any way by any party without priorwritten consent from Harken, Inc.DIMENSIONS IN OVALS ARE KEYPRODUCT CHARACTERISTICSUNLESS OTHERWISE SPECIFIED:- DIMENSIONS IN INCHES- ALL DIMENSIONS PRIOR TO FINISHING- REMOVE ALL BURRS AND BREAK SHARPEDGES WITH 0.010 MAX RADIUS ORCHAMFERDATE:DATE:DATE:SHEET NUMBER:DESIGN BY : DATE:VARIOUSLOAD TENDER H-86666-ORLY-CJL 9/24/20210--MGKDOUBLE BECKET BLOCK10/15/20211:19/10/20211/1JDM 9/9/2021-PRODUCT MARKINGSRed Block:WORKING LOAD:3 kN (675 lb)BREAK LOAD:45 kN (10,116 lb)Load Diagram:WLL & Rope DiameterSerial NumberProduct NumberIntended UseManufacturerDRAWING NUINCORPORATEDPRODUCT CHARACTERISTICS- DIMENSIONS IN INCHES- ALL DIMENSIONS PRIOR TO FINISHING- REMOVE ALL BURRS AND BREAK SHARPEDGES WITH 0.010 MAX RADIUS ORCHAMFERVARIOUSLOAD TENDER---- -INCORPORATEDP- ALL D- REMOVEDGEFOR PROTOTYPING PURPOSES ONLYFOR QUOTATION PURPOSES ONLYSURFACE FINISH:MATERIAL:DRAWING NUMBER REV.FINISH:PART #MFG. APR :DRAWN BY :TOLERANCES UNLESS OTHERWISE SPECIFIED:DECIMAL:ANGULAR:SCALE:ENG. APR :INCORPORATEDN15 W24983 Bluemound RoadPewaukee, Wisconsin 53072Tel: 262-691-3320Fax: 262-691-3807www.harken.com© The designs, constructions, arrangements, disclosures and devicesillustrated in presentations bearing this note are the property of Harken, Inc,Pewaukee, WI and are submitted in confidence with the understandingthat such material shall not be utilized in any way by any party without priorwritten consent from Harken, Inc.DIMENSIONS IN OVALS ARE KEYPRODUCT CHARACTERISTICSUNLESS OTHERWISE SPECIFIED:- DIMENSIONS IN INCHES- ALL DIMENSIONS PRIOR TO FINISHING- REMOVE ALL BURRS AND BREAK SHARPEDGES WITH 0.010 MAX RADIUS ORCHAMFERDATE:DATE:DATE:SHEET NUMBER:DESIGN BY : DATE:ING THREADS.VARIOUSLOAD TENDER H-86666-ORLY-CJL 9/24/20210--MGKDOUBLE BECKET BLOCK10/15/20211:19/10/20211/1JDM 9/9/2021-FOR MATERIALHANDLING ONLYDO NOTREPLACE ROPEMH674 lb WLL674 lb WLLFOR PROTOTYPING PURPOSES ONLYFOR QUOTATION PURPOSES ONLYSURFACE FINISH:MATERIAL:DRAWING NUMBER REV.FINISH:PART #MFG. APR :DRAWN BY :TOLERANCES UNLESS OTHERWISE SPECIFIED:DECIMAL:ANGULAR:SCALE:ENG. APR :INCORPORATEDN15 W24983 Bluemound RoadPewaukee, Wisconsin 53072Tel: 262-691-3320Fax: 262-691-3807www.harken.com© The designs, constructions, arrangements, disclosures and devicesillustrated in presentations bearing this note are the property of Harken, Inc,Pewaukee, WI and are submitted in confidence with the understandingthat such material shall not be utilized in any way by any party without priorwritten consent from Harken, Inc.DIMENSIONS IN OVALS ARE KEYPRODUCT CHARACTERISTICSUNLESS OTHERWISE SPECIFIED:- DIMENSIONS IN INCHES- ALL DIMENSIONS PRIOR TO FINISHING- REMOVE ALL BURRS AND BREAK SHARPEDGES WITH 0.010 MAX RADIUS ORCHAMFERDATE:DATE:DATE:SHEET NUMBER:DESIGN BY : DATE:OTE:REFER TO ELECTRONIC FILE FOR ALL DIMENSIONS NOT SHOWN.SEE TITLE BLOCK FOR TOLERANCE OF NON DIMENSIONED FEATURES.REFER TO HS-200 HARKEN THREAD STANDARD FOR ALL DIMENSIONS REGARDING THREADS.VARIOUSLOAD TENDER H-86666-ORLY-CJL 9/24/20210--MGKDOUBLE BECKET BLOCK10/15/20211:19/10/20211/1JDM 9/9/2021-HARKEN INC.No etching on this sideof upper block.Material Handling WINGMAN - Red annodized, black ropeMHINCORPORATEDP- ALL D- REMOVEDGEINCORPORATEDP- ALL D- REMOVEDGEDRAWING NUINCORPORATEDPRODUCT CHARACTERISTICS- DIMENSIONS IN INCHES- ALL DIMENSIONS PRIOR TO FINISHING- REMOVE ALL BURRS AND BREAK SHARPEDGES WITH 0.010 MAX RADIUS ORCHAMFERVARIOUSLOAD TENDER---- -Cam (or Silver) Block:ManufacturerCountry ofManufactureRope DiameterRelease Direction Product BrandRelease HandlePLEASE SAVE THESE INSTRUCTIONS

/ 2

Related manuals for Harken IN172.3m