Garmin GPSMAP 8008 MFD Instructions Manual

Also see for GPSMAP 8000 Series: Owner's manual Owner's manual Quick start manual Owner's manual Installation instructions

Contents

Garmin GPSMAP 8008 MFD Instructions Manual Manual pdf 1 page image

GPSMAP® 8000 Series InstallationInstructionsImportant Safety InformationWARNINGSee the Important Safety and Product Information guide in theproduct box for product warnings and other importantinformation.When connecting the power cable, do not remove the in-linefuse holder. To prevent the possibility of injury or productdamage caused by fire or overheating, the appropriate fusemust be in place as indicated in the product specifications. Inaddition, connecting the power cable without the appropriatefuse in place will void the product warranty.CAUTIONAlways wear safety goggles, ear protection, and a dust maskwhen drilling, cutting, or sanding.NOTICEWhen drilling or cutting, always check what is on the oppositeside of the surface.Registering Your DeviceHelp us better support you by completing our online registrationtoday.• Go to http://my.garmin.com.• Keep the original sales receipt, or a photocopy, in a safeplace.Contacting Garmin Product Support• Go to www.garmin.com/support and click Contact Supportfor in-country support information.• In the USA, call (913) 397.8200 or (800) 800.1020.• In the UK, call 0808 2380000.• In Europe, call +44 (0) 870.8501241.Tools Needed• Drill and drill bits• #2 Phillips screwdriver• Marine sealant• Jigsaw• File and sandpaperMounting the ComponentsMounting ConsiderationsNOTICEThis device should be mounted in a location that is not exposedto extreme temperatures or conditions. The temperature rangefor this device is listed in the product specifications. Extendedexposure to temperatures exceeding the specified temperaturerange, in storage or operating conditions, may cause devicefailure. Extreme-temperature-induced damage and relatedconsequences are not covered by the warranty.You can mount the device using one of three methods. You canuse the included bracket and hardware to bail mount the device,you can use the included template and hardware to flush mountthe device, or you can use the flat-mount kit (sold separately) tomount the device flat with the dashboard. When selecting amounting location, observe these considerations.NOTE: Not all mounting methods are available for all devicemodels. See the specific mounting-type section for more detailsabout your model.• The location should provide optimal viewing as you operateyour boat.• The location should allow for easy access to all deviceinterfaces, such as the keypad, touchscreen, and cardreader, if applicable.• The location must be strong enough to support the weight ofthe device and protect it from excessive vibration or shock.• To avoid interference with a magnetic compass, the deviceshould not be installed closer to a compass than thecompass-safe distance value listed in the productspecifications.• The location must allow room for the routing and connectionof the cables.Bail Mounting the DeviceNOTICEIf you are mounting the bracket on fiberglass with screws, it isrecommended to use a countersink bit to drill a clearancecounterbore through only the top gel-coat layer. This will help toavoid any cracking in the gel-coat layer when the screws aretightened.The bail-mounting hardware (screws and washers or nuts,washers, and bolts) is not included. The holes on the bail-mountbracket are 5/16 in. (7.9 mm) in diameter. Before you can bailmount the device, you must choose mounting hardware that fitsthe holes in the bail-mount bracket and securely attaches it toyour specific mounting surface. The size of the pilot holerequired depends on the mounting hardware you choose.You can bail mount only the eight-inch and 12-inch models. Dueto the size of the 15-inch models, you must install them usingthe flush-mount or flat-mount method.1 Using the included bail-mount bracket À as a template, markthe location of the four pilot holes Á.2 Using a drill bit appropriate for your mounting hardware, drillthe pilot holes.3 Secure the bail-mount bracket to the surface using yourmounting hardware Â.4 Install the bail-mount knobs Ã on the sides of the device.December 2012 190-01557-02_0A Printed in Taiwan