GPSMAP®702/902 SERIESINSTALLATIONINSTRUCTIONSImportant Safety InformationWARNINGSee the Important Safety and Product Information guide in theproduct box for product warnings and other importantinformation.When connecting the power cable, do not remove the in-linefuse holder. To prevent the possibility of injury or productdamage caused by fire or overheating, the appropriate fusemust be in place as indicated in the product specifications. Inaddition, connecting the power cable without the appropriatefuse in place voids the product warranty.CAUTIONAlways wear safety goggles, ear protection, and a dust maskwhen drilling, cutting, or sanding.NOTICEWhen drilling or cutting, always check what is on the oppositeside of the surface.To obtain the best performance and to avoid damage to yourboat, install the device according to these instructions.Read all installation instructions before proceeding with theinstallation. If you experience difficulty during the installation,contact Garmin®Product Support.Contacting Garmin Support• Go to support.garmin.com for help and information, such asproduct manuals, frequently asked questions, videos, andcustomer support.• In the USA, call 913-397-8200 or 1-800-800-1020.• In the UK, call 0808 238 0000.• In Europe, call +44 (0) 870 850 1241.Updating the Device SoftwareYou may need to update the device software when you installthis device or add an accessory to the network. You can useone of two methods to update the software.• Use the ActiveCaptain™ app.• Download the update from www.garmin.com/support/software/marine.html using a 32 GB card and a computerrunning Windows®operating system.For more information, see the owner's manual atwww.garmin.com/manuals/GPSMAP702-902.Registering Your DeviceHelp us better support you by completing our online registrationtoday. You can register your device using one of two methods.• Use the ActiveCaptain app.• Go to my.garmin.com/registration and sign into your Garminaccount to register the device.Keep the original sales receipt, or a photocopy, in a safe place.After you add devices to the chartplotter network, register thenew devices.Tools Needed• Drill• Drill bits appropriate for the device and mounting styleMounting Style Drill Bit SizesBail with included M4 wood screws 3.2 mm (1/8 in.)Flush 13 mm (1/2 in.)Flush with included M3.5 wood screws (702 series) 2 mm (5/64 in.)Flush with included M4 wood screws (902 series) 3.2 mm (1/8 in.)Flush with included machine screws and nut plates 6 mm (1/4 in.)4 mm (3/16 in.)Flush with included M3.5 machine screws andtapped holes (702 series)M3.5 tapFlush with included M4 machine screws and tappedholes (902 series)M4 tap• #2 Phillips screwdriver• Jigsaw or rotary tool• File and sandpaper• Marine sealant (recommended)Mounting ConsiderationsNOTICEThis device should be mounted in a location that is not exposedto extreme temperatures or conditions. The temperature rangefor this device is listed in the product specifications. Extendedexposure to temperatures exceeding the specified temperaturerange, in storage or operating conditions, may cause devicefailure. Extreme-temperature-induced damage and relatedconsequences are not covered by the warranty.When selecting a mounting location, you should observe theseconsiderations.• The location should provide optimal viewing as you operateyour boat.• The location should allow for easy access to all deviceinterfaces, such as the keypad, touchscreen, and cardreader, if applicable.• The location must be strong enough to support the weight ofthe device and protect it from excessive vibration or shock.• To avoid interference with a magnetic compass, the deviceshould not be installed closer to a compass than thecompass-safe distance value listed in the productspecifications.• The location must allow room for the routing and connectionof all cables.• The location must not be a flat, horizontal surface. Thelocation should be in a vertical angle.The location and viewing angle should be tested before youinstall the device. High viewing angles from above and belowthe display may result in a poor image.Bail Mounting the DeviceNOTICEIf you are mounting the bracket on fiberglass with screws, it isrecommended to use a countersink bit to drill a clearancecounterbore through only the top gel-coat layer. This will help toavoid cracking in the gel-coat layer when the screws aretightened.October 2018190-02141-02_0D