GE Range Installation Instructions Manual

Also see for Range: Installation instructions Owner's manual Installation instructions Installation instructions Installation instructions

Contents

installation instructions

GE Range Installation Instructions Manual Manual pdf 1 page image

TOOLS YOU WILL NEED MATERIALS YOU MAY NEED Gas line shut-off valve Pipe joint sealant or UL-approved pipe threadtape with Teflon* that resists action of naturaland LP gases Flexible metal appliance connector (1/2” I.D.).A 5-foot length is recommended for ease ofinstallation but other lengths are acceptable.Never use an old connector when installing anew range. Flare union adapter for connection to gassupply line (3/4” or 1/2” NPT x 1/2” I.D.) Flare union adapter for connection to pressureregulator on range (1/2” NPT x 1/2” I.D.) Liquid leak detector orsoapy water. Squeeze Connector(For Conduit Installations Only) (UL Listed 40 AMP)4-Wire Cord 4’ long OR3-Wire Cord 4’ long*Teflon: Registered trademark of DuPontFlat-bladescrewdriverPipe wrenches (2)(one for backup)PhillipsscrewdriverDrill with 1/8” BitTin SnipsTape MeasureOpen-end oradjustable wrenchSafety GlassesPliers1/4” Nut DriverPencil and ruler LevelDrill, awl or nailIN THE COMMONWEALTH OFMASSACHUSETTS This product must be installed by a licensedplumber or gas fitter. When using ball type gas shut-off valves, theyshall be the T-handle type. A flexible gas connector, when used, must notexceed 3 feet.Installation InstructionsRangeQuestions? Call 1.800.GE.CARES (1.800.432.2737) or visit www.GEAppliances.comBEFORE YOU BEGIN,03257$17³ Save these instructions forlocal inspector’s use.,03257$17³ Observe all governingcodes and ordinances.,03257$17³ Remove all packingmaterial and literature from oven beforeconnecting gas and electrical supply to range.,03257$17³ To avoid damage to yourcabinets, check with your builder or cabinetsupplier to make sure that the materials used willnot discolor, delaminate or sustain other damage.This oven has been designed in accordance withthe requirements of UL and CSA Internationaland complies with the maximum allowable woodcabinet temperatures of 194°F (90°C).Note to Installer – Be sure to leave theseinstructions with consumer.Note to consumer – Keep these instructions forfuture reference.Servicer – The electrical diagram is in anenvelope attached to the back of the range.Proper installation is the responsibility of theinstaller.Product failure due to improper installation is notcovered under warranty.Before installing your range on linoleum or anyother synthetic floor covering, make sure thefloor covering can withstand 180°F withoutshrinking, warping or discoloring. Do not installthe range over carpeting unless a sheet of 1/4”thick plywood or similar insulator is placedbetween the range and carpeting.Mobile Home - Additional InstallationRequirementsThe installation of this range must conform tothe Manufactured Home Construction and SafetyStandard, Title 24 CFR, Part 3280 (formerly theFederal Standard for Mobile Home Constructionand Saftey, Title 24, HUD Part 280). When suchstandard is not applicable, use the Standard forManufactured Home Installations, ANSI A225.1/NFPA 501A or with local codes.In Canada, the installation of this range mustconform with the current standards CAN/CSA-A240-latest edition, or with local codes.When this range is installed in a mobile home, itmust be secured to the floor during transit. Anymethod of securing the range is adequate aslong as it conforms to the standards listed above.WARNINGFIRE OR EXPLOSION HAZARDIf the information in this manual is not followedexactly, a fire or explosion may result causingproperty damage, personal injury or death.Installation must be performed by a qualifiedinstaller.Read these instructions completely and carefully.Installation of this range must conform withlocal codes, or in the absence of local codes,with the National Fuel Gas Code, ANSI Z223.1/NFPA.54, latest edition. In Canada, installationmust conform with the current Natural GasInstallation Code, CAN/CGA-B149.1 or the currentPropane Installation Code, CAN/CGA-B149.2, andwith local codes where applicable. This rangehas been design-certified by CSA Internationalaccording to ANSI Z21.1, latest edition andCanadian Gas Association according to CAN/CGA-1.1 latest edition.When installing a gas appliance the use of oldflexible connectors can cause gas leaks andpersonal injury. Always use a NEW flexibleconnector.Leak testing of the appliance shall be conductedaccording to the manufacturer instructions.The range must be electrically grounded inaccordance with local codes or, in the absenceof local codes, in accordance with the NationalElectrical Code (ANSI/NFPA 70, latest edition).In Canada, electrical grounding must be inaccordance with the current CSA C22.1 CanadianElectrical Code Part 1 and/or local codes. SeeElectrical Connections in this section.Do not install this product with an air curtainhood or other range hood that operates byblowing air down on the cooktop. This airflowmay interfere with operation of the gas burnersresulting in fire or explosion hazard.FOR YOUR SAFETY:& ! & #& $ ! & "& ! ! !! ! "%WARNINGWARNING Before beginningthe installation, switch power off atservice panel and lock the servicedisconnecting means to prevent powerfrom being switched on accidentally.When the service disconnecting meanscannot be locked, securely fasten aprominent warning device, such as atag, to the service panel.If you did not receive an anti-tip bracket with yourpurchase, call 1.800.626.8774 to receive one at nocost. (In Canada, call 1.800.561.3344.) For installationinstructions of the bracket, visit: www.GEAppliances.com.(In Canada, www.GEAppliances.ca.)Anti-Tip BracketKit IncludedSH 1 of 2 31-10898-2 07-13 GECONVERTING TO LP GAS(OR CONVERTING BACK TONATURAL GAS FROM LP)This range leaves the factory set for use withnatural gas. If you want to convert to LPgas, the conversion must be performed by aqualified LP gas installer.The conversion orifices and instructions can befound on back of the range.Keep these instructions and all orifices in caseyou want to convert back to natural gas.DIMENSIONS AND CLEARANCESProvide adequate clearances between therange and adjacent combustible surfaces. Thesedimensions must be met for safe use of yourrange.Allow 30” (76.2 cm) minimum clearance betweenburners and bottom of unprotected wood ormetal cabinet, or allow a 24” (61 cm) minimumwhen bottom of wood or metal cabinet isprotected by no less than 1/4” (6.4 mm) thickflame-retardant millboard covered with no lessthan No. 28 MSG sheet metal (.015” [.38 mm]thick), .015” (.38 mm) thick stainless steel, .025”(0.64 mm) aluminum or .020” (0.5 mm) copper.Installation of a listed microwave oven orcooking appliance over the cooktop shallconform to the installation instructions packedwith that appliance.For island installation, maintain 2-1/2” minimumfrom cutout to back edge of countertop and3” minimum from cutout to side edges ofcountertop.To cabinetsbelow cooktopand at therange backMinimum tocabinets oneither sideof the range 30”30”Minimum 13”6”Minimumclearance toright wallMaximumdepth forcabinets abovecountertopsFront edgeof the rangeside panelforward fromcabinet 0”To cabinetsbelow cooktopand at therange back6”Minimumclearanceto left wall0”18”2 1/2"47 1/2"29 3/16"w/ handle26 1/2"w/o handle30"36 1/2"31 1/4"Rear of RangeOrifice Box(locationmay vary)1/4”CAUTION To prevent draftsfrom affecting burner operation, sealall openings in floor under applianceand behind appliance wall.DIMENSIONS AND CLEARANCES (CONT.)GAS PIPE AND ELECTRICAL OUTLET LOCATIONS35” to36-1/2”from floor tocountertop24”MaxRecommended area for120V outlet on rear wall andarea for through-the-wallconnection of pipe stub andshut-off valve.Recommended areafor through-the-floorconnection of pipe stuband shut-off valve.

/ 2

Related manuals for GE Range