GE Appliances P2B930 Owner's Manual And Installation Instructions

Also see for Appliances C2S985: Owner's Manual & Installation Instructions Owner's Manual & Installation Instructions Owner's manual and installation instructions Technical service guide Owner's Manual & Installation Instructions

GE Appliances P2B930 Owner's Manual And Installation Instructions Manual pdf 38 page image

I statl tiI structiIf you have questions, cai! 1.800.GE.CARES or visit our Website at: GEAppliances.comRa eIn the Commonwealth of Massachusetts, This product must be installed by a licensed plumber orgas fitter., When using ball type gas shut-off valves, they shall bethe T-handle type., A flexible gas connector, when used,must not exceed 3 feet.BEFORE YOU BEGINReed these instructions completely end carefully.Installation of this range must conform with localcodes, or in the absence of local codes, with theNational Fuel Gas Code, ANSI Z223.1/NFPA.54, latestedition. In Canada, installation must conform withthe current Natural Gas Installation Code, CAN/CGA-B149.1 or the current Propane InstallationCode, CAN/CGA-B149.2, end with local codes whereapplicable. This range has been design-certified by CSAInternational according to ANSI Z21.1, latest editionand Canadian Gas Association according to CAN/CGA-I.1 latest edition.As with any appliance using gas and generating heat,there are certain safety precautions you should follow.You will find these precautions in the Important SafetyInformation section in the front of this manual. Readthem carefully." IMPORTANT - Save these instructions forlocal electrical inspector's use.. IMPORTANT - Observeallgoverningcodes and ordinances., Note to InstaJJer - Leave these instructions withthe appliance after installation is completed.. Note to Consumer - Keep this Owner's Manualand Installation Instructions for future reference., Note - This appliance must be properly grounded., Servicer - The electrical diagram is in an envelopeattached to the back of the range., Proper installation is the responsibility of the installer., Product failure due to improper installation is notcovered under the Warranty.Mobile Home - Additional Installation RequirementsThe installation of this range must conform to theManufactured Home Construction and Safety Standard,Title 24 CFR, Part 3280 (formerly the Federal Standardfor Mobile Home Construction, use the Standard forManufactured Home Installations, ANSI A225, 1/NFPA501A or with local codes.Mobile home installations require:" When this range is installed in a mobile home, it mustbe secured to the floor during transit. Any method ofsecuring the range is adequate as long as it conforms tothe standards listed above.FOR YOUR SAFETYDo not store or use combustible materials, gasolineor other flammable vapors and liquids in the vicinityof this or any other appliance.If you smell gas:O Open windows.Don't touch electrical switches.O Extinguish any open flame.Olmmediately call your gas supplier.TOOLS YOU WILL NEEDPhillipsscrewdriverFlat-bladescrewdriver_SJ _'_ _ ,,,.,.,.,., .,..,..,J.,,,,.,.L..Penciland rulerPipewrenches (2)(one for backup)Open-end oradjustable wrenchLevelDrill,awl or nail38MATERIALS YOU HAY NEED, Gas line shut-off valve, Pipejoint sealant or UL-approved pipe thread tape withTeflon* that resists action of natural and LPgases, Flexible metal appliance connector (1/2" I.D.)A 5-footlength is recommended for ease of installation but otherlengths are acceptable. Never use an old connectorwhen installing a new range., Flare union adapter for connection to gas supply line(3/4" or 1/2" NPTx 1/2" I.D.), Flare union adapter for connection to pressure regulatoron range (1/2" NPTx 1/2" I.D.), Liquid leak detector or soapy water., Lag bolt or 1/2" O.D.sleeveanchor (for concrete floors only)., SqueezeConnectormatchingthe sizeof the bracketopening(onthe range back behindthe wiringcover)and the houseconduit.Obtainonly if replacingthe power cordwith conduit.*Teflon: Registered trademark of DuPont