FUJITSU StorageETERNUS DX100 S4/DX200 S4,ETERNUS DX100 S3/DX200 S3Hybrid Storage SystemsSite Planning GuideRequirements for transportation/installationP3AM-7632-18ENZ0

Fujitsu ETERNUS DX100 S4 Site Planning Manual

Chapter 1 Workflow

Chapter 2 Checking the Server Environment

Chapter 3 Notes

LVM Notes

Chapter 4 Checking the Server Information

Chapter 5 Setting Up the ETERNUS DX

Chapter 6 Installing the iSCSI Software Initiator and Setting Up the Server

Setting Up the Server

Maximum Number of Volume Group Settings

Server Settings when CHAP Authentication is Used

Server Settings when Bidirectional CHAP Authentication is Used

Chapter 7 Checking Connections

Multipath Configuration using PV-Links

Multipath Configuration using Native Multipath

Enabling ALUA (alua_enabled)

ETERNUS DX100 S3

using this manual

compliance with standards

about this manual

symbols used in this manual

safety precautions

power synchronized unit

Chapter 1 Overview

Features

Specifications

Components

Table 1.2 Status and meanings of each LED (for power synchronized units)

AC Sensor Unit (Optional)

System Configuration

Figure 1.6 System configuration example (power synchronization with three or more server UPS units)

Power Management for Power Synchronization

Figure 1.8 Operation timing chart when using a power synchronized unit (powering on)

Figure 1.9 Power off using a power synchronized unit

Figure 1.10 Operation timing chart when using a power synchronized unit (powering off)

Chapter 2 Installation

Preparation

Installing in a Rack

Installing a Power Synchronized Unit

Installing an AC Sensor Unit

Chapter 3 Powering On and Off

Chapter 4 Connection and Settings

Setting the ETERNUS DX/AF

Figure 4.2 ETERNUS DX8700 S3/DX8900 S3 setup (Setup Power Management screen)

Figure 4.3 ETERNUS DX80 S2/DX90 S2 setup (Setup Power Management screen)

Figure 4.4 ETERNUS DX60 S2 setup (Setup Power Management screen)

Turning on the Power Synchronized Unit

Connecting Cascade Cables

Connecting to the Server UPS Unit

Connecting the Server UPS Unit to the Power Synchronized Unit

Connecting the AC Sensor Unit

Connecting to the ETERNUS DX/AF

Checking after Connection

Chapter 5 Adding a Connecting Device

Connection Procedure When Adding an ETERNUS DX/AF

Chapter 6 Operation and Maintenance

Replacing a Power Synchronized Unit

Troubleshooting

Trouble Record

structure of this manual

naming conventions

operating environment

Chapter 1 Screen Operations

hardware components

Screen Structures

List Screen/Detailed Screen

Basic Operation

Chapter 2 System Status

System (Basic Information)

Network

Remote Support

support information

AIS Connect

Root Certificate

Key Management

Key Group

Define Role

Eco-mode

Eco-mode Schedule Detail

Event/Dump

Audit Log

Firmware Maintenance

Storage Migration

Path Group Detail Information

Utility

System Settings

Chapter 3 Component Status

Storage (Basic Information)

Controller Enclosure

Controller Module

Performance (CM)

Port Error Statistics (for the ETERNUS AF250 and the ETERNUS DX200F)

Channel Adapter

Performance (CA)

PCIe Flash Module

Performance (PCIe Flash Module)

Bootup and Utility Device

Power Supply Unit (CE)

Battery

Frontend Enclosure

Frontend Router

Power Supply Unit (FE)

FAN Unit

Operation Panel

Drive Enclosure

I/O Module

Port Error Statistics

Power Supply Unit (DE)

Fan Expander Module

Drives

Performance (Drive)

Drive Error Statistics

Controller Enclosure Detail

Controller Module Detail

Channel Adapter Detail

PCIe Flash Module Detail

PSU/CPSU (CE) Detail

Frontend Router Detail

Service Controller Detail

FE Power Supply Unit Detail

FAN Unit Detail

Drive Enclosure Detail

I/O Module Detail

Power Supply Unit (DE) Detail

Fan Expander Module Detail

Drive Detail

Bootup and Utility Device Detail

SAS Cable Detail

Frontend Cable Detail

Management Cable Detail

Port Detail

Chapter 4 Volume Status

Volume (Basic Information)

Performance (Host I/O)

Performance (QoS)

Performance (Advanced Copy)

LUN Group

Reservation

Pinned Data

Bad Sector

Balancing Thin Provisioning Volume

Snapshot

Volume Detail (Basic)

Volume Detail (Reservation)

Volume Detail (Pinned Data)

Volume Detail (Balancing TPV)

Volume Detail (Used RAID Group)

Volume Detail (Snapshot)

Chapter 5 Connectivity Status

Connectivity (Basic Information)

Host Affinity Detail (Host Group - CA Port Group - LUN Group Setting)

Host Affinity Detail (Host - CA Port - LUN Group Setting)

Host Group

drive enclosures

Chapter 1 Component Names

Rear

Figure 1.4 Rear Views of a Controller Enclosure (When Two Controllers are Installed)

Drive Enclosures

Figure 1.7 Front View of a High-density Drive Enclosure

Figure 1.9 Rear Views of a Drive Enclosure (When Two I/O Modules are Installed)

Power Distribution Units (for Regions Other than EMEA&I)

Figure 1.13 Power distribution unit for DX100 S3/DX200 S3 (AC200-240V, 2U, 16Outlets)

Chapter 2 Rack Installation

Installing Power Distribution Unit (for Regions Other than EMEA&I)

Installing Power Distribution Unit (1U)

Installing Power Distribution Unit (2U)

Controller Enclosure Installation (for Regions Other than EMEA&I)

Type Drive Enclosure Installation (for Regions Other than EMEA&I)

High-density Drive Enclosure Installation (for Regions Other than EMEA&I)

Chapter 3 Checking the Configuration Environment

Server Connection Preparation

Driver Installation

iSCSI Initiator Parameter Settings

Preparing the PC Terminal for Setup

LAN Connection Preparation for Operation Management

LAN Related Specifications

Chapter 4 Connecting Cables

Drive Enclosure Connection

Figure 4.1 Connecting Cables Between Enclosures (When Only One Controller is Installed)

Fujitsu ETERNUS DX100 S4 Site Planning Manual

Product

Learn More

Legal