Fujitsu ETERNUS DX200 S4 manuals
ETERNUS DX200 S4
Table of contents
- using this manual
- compliance with standards
- about this manual
- symbols used in this manual
- safety precautions
- power synchronized unit
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Chapter 1 Overview
- Features
- Specifications
- Components
- Table 1.2 Status and meanings of each LED (for power synchronized units)
- AC Sensor Unit (Optional)
- System Configuration
- Figure 1.6 System configuration example (power synchronization with three or more server UPS units)
- Power Management for Power Synchronization
- Figure 1.8 Operation timing chart when using a power synchronized unit (powering on)
- Figure 1.9 Power off using a power synchronized unit
- Figure 1.10 Operation timing chart when using a power synchronized unit (powering off)
- Chapter 2 Installation
- Preparation
- Installing in a Rack
- Installing a Power Synchronized Unit
- Installing an AC Sensor Unit
- Chapter 3 Powering On and Off
- Chapter 4 Connection and Settings
- Setting the ETERNUS DX/AF
- Figure 4.2 ETERNUS DX8700 S3/DX8900 S3 setup (Setup Power Management screen)
- Figure 4.3 ETERNUS DX80 S2/DX90 S2 setup (Setup Power Management screen)
- Figure 4.4 ETERNUS DX60 S2 setup (Setup Power Management screen)
- Turning on the Power Synchronized Unit
- Connecting Cascade Cables
- Connecting to the Server UPS Unit
- Connecting the Server UPS Unit to the Power Synchronized Unit
- Connecting the AC Sensor Unit
- Connecting to the ETERNUS DX/AF
- Checking after Connection
- Chapter 5 Adding a Connecting Device
- Connection Procedure When Adding an ETERNUS DX/AF
- Chapter 6 Operation and Maintenance
- Replacing a Power Synchronized Unit
- Troubleshooting
- Trouble Record
ETERNUS DX200 S4
Table of contents
- Table Of Contents
- Preface
- Overview of Non-Stop Storage Solution
- Protecting Investment and Optimizing Investment Cost
- System Configuration
- Example of a Non-Stop Storage Configuration
- management server
- Example of a Non-Stop Storage Configuration (with Redundant Management Servers)
- Hardware Layout
- Workflow for System Configuration
- Conclusion
ETERNUS DX200 S4
Table of contents
- about this manual
- naming conventions
- symbols used in this manual
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Chapter 1 Component Names and LED Names
- Rear
- Figure 1.4 Rear View of a Controller Enclosure (When Two Controllers Are Installed)
- Components (Front)
- Figure 1.6 2.5" Drives
- ETERNUS DX100 S4/DX200 S4 Components (Rear)
- Figure 1.10 Controller (ETERNUS DX100 S4/DX200 S4)
- Table 1.3 Status and Meanings of Each LED (Controller)
- Figure 1.11 FC Interface (Installed in a Controller)
- Figure 1.13 Host Interface for FC Cable Connections (Equipped with SFP+ Modules in All Ports and Installed in the Controllers)
- Figure 1.15 iSCSI 10Gbit/s (10GBASE-T) Interface, iSCSI 1Gbit/s Interface (Installed in a Controller)
- Figure 1.17 Ethernet 1Gbit/s Interface (Installed in a Controller)
- ETERNUS DX100 S3/DX200 S3 Components (Rear)
- Figure 1.19 Controller (ETERNUS DX100 S3/DX200 S3)
- Table 1.5 Status and Meanings of Each LED (Controller)
- Figure 1.20 FC Interface (Installed in a Controller)
- Figure 1.22 Host Interface for Copper Twinax Cable Connection (Installed in a Controller)
- Figure 1.24 SAS Interface (Installed in a Controller)
- Figure 1.26 Power Supply Unit (Controller Enclosure)
- Type Drive Enclosures
- Figure 1.32 2.5" Drives
- Figure 1.34 3.5" Drives
- Components (Rear)
- Figure 1.37 Power Supply Unit (2.5"/3.5" Type Drive Enclosure)
- High-density Drive Enclosure
- Figure 1.41 Disk Activity Panel (DAP)
- Components (Internal)
- Figure 1.45 Fan Expander Module
- Figure 1.46 Power Supply Unit (High-density Drive Enclosure)
- Power Distribution Units (for Regions other than the EMEIA, North American, Central American and Caribbean Regions)
- Power Distribution Units (2U)
- Chapter 2 Basic Operation
- Figure 2.2 ON Position (Marked "|") of the Main Line Switches on a 2U Power Distribution Unit
- Figure 2.4 OFF Position (Marked "¡") of the Main Line Switches on a 2U Power Distribution Unit
- Switching On and Off the PSU Switch on the Power Supply Unit
- Figure 2.6 OFF Position (Marked "¡") of the PSU Switch of a Power Supply Unit
- Powering On
- Powering Off
- Using the FUNCTION Button
- Chapter 3 Storage System Monitoring
- Displaying Status via ETERNUS CLI
- Event Notification
- Audit Log
- Chapter 4 Process Time (Estimated)
- Rebuild/Copyback Process Time
- Chapter 5 Component Expansion/Function Enhancement
- Drive Handling Instructions
- Additional Drive Installation Procedure
- Installing Additional Drive Enclosures
- Additional Drive Enclosure Installation Procedure
- Installing Long Wave SFP+ Modules (16Gbit/s)
- Long Wave SFP+ Modules (16Gbit/s) Installation Procedure
- Adding Servers
- Volume Creation
- Connection Setup
- Chapter 6 Maintenance
- Related Service
- Check List
- Required Information for Inquiries