Copyright © 2010 SEIKO EPSON CORPORATION. All rights reserved. EM107B2068FRC620 Vision Guide 6.0 USB License Key Mounting Procedure1. USB Bracket AppearanceUse the bracket to mount the USB license key to RC620 controller.USB connector (Connect USB license key here.)USB cable (Connect to CPU board.)USB license key securing part(Holds key with attached wire tie.)2. Securing USB License KeyConnect the USB license key to the USB connector.Firmly secure the USB license key to the bracket using the attached wire tie.USB license keySecure USB license key to bracketusing wire tie

Epson RC620 Manual

Safety

Design and Installation Safety

Designing a Safe Robot System

Operation Safety

Safety-related Requirements

Part Names / Arm Motion

Operation Modes

Maintenance Safety

Emergency Stop

Free running distance in emergency

How to reset the emergency mode

Labels

Manipulator

Safety Features

Lockout / Tagout

Manipulator Specifications

Installation

Environment

Noise level

Base Table

Installation Procedure

Controller Installation

Installation - Control Unit RC620

Installation - Drive Unit RC620DU

and Latch Release Switch

Safety Door Switch

Operation

Emergency Stop Switch

Pin Assignments

Circuit Diagrams - Control Unit

Circuit Diagrams - Drive Unit

AC power cable

Breaker

Drive Unit Connection

Drive Unit Configuration

Connecting Manipulator and Controller

Power-on

First Step

How to set the Independent mode

Inspection While the Power is OFF

Inspection While the Power is ON

Tightening Hexagon Socket Head Cap

Manuals 200

RC620 Series

Safety Precautions

RC620 Rev

Specifications

Standard Specifications

Outer Dimensions

Part Names and Functions

Functions

Power Supply

AC Power Cable

Typical Cable Connection

Connecting Manipulator to Controller

Noise Countermeasures

Operation Mode (TEACH/AUTO)

Program Mode (AUTO)

Auto Mode (AUTO)

Setup from Control Device

Memory Port

Adoptable USB Memory

Controller Status Storage with Teach Pendant (Option)

Transfer with E-mail

Details of Data

LAN (Ethernet Communication) Port

IP Address

EMERGENCY

Safety Door Switch and Latch Release Switch

Latch Release Switch

Emergency Stop Switch Connection

Circuit Diagrams

External safety relay typical application

I/O Connector

Output Circuit

Pin Assignment

I/O Remote Settings

R-I/O Connector

Expansion I/O Board

Option Units

Fieldbus I/O Board

RS-232C Board

RS-232C Software Communication Setup (RS-232C)

Option : Teach Pendant TP1

Operation Mode (TEACH / AUTO)

Operation Panel (Key Description)

Enable Switch

Teaching Procedure

Teaching

Direct Teaching

TEACH Mode

Jog & Teach

Point Editor

Robot

Motion Command

I/O Command

Jog Distance

Free Joints

AUTO Mode

Program Command Display

I/O Monitor

Task Monitor

System History

Controller Statuses Preservation

Brightness / Contrast

Error

Troubleshooting

Option : RAID

Status for Restore

Restoring the Data Protection Status

Safety Precautions on Maintenance

Regular Maintenance Inspection

Inspection Point

Controller Structure

Connector Pin Assignment

M/C Signal Connector

Backup and Restore

Backup Data Types

Backup

Restore

Firmware Update

Controller Recovery

Firmware Initialization Procedure

Maintenance Parts Replacement Procedures

Replacing the Large Fan

Replacing the Small Fan

Battery

Introduction

DeviceNet

General Specifications

PROFIBUS DP

EtherNet/IP

CC-Link

PROFINET

PROFINET Communication

DeviceNet Network Construction

DeviceNet Master Board Installation

DeviceNet Slave Board Installation

PROFIBUS-DP Master Board Installation

PROFIBUS-DP Slave Board Installation

EtherNet/IP Master Board Installation

EtherNet/IP Slave Board Installation

Using FbusIO_SendMsg

Explicit Message Connection (for DeviceNet, EtherNet/IP)

Remote Control Input and Output Setting

Problems and Countermeasures

Procedures for Examining Possible Causes

PROFIBUS DP Troubleshooting

EtherNet/IP Troubleshooting

Maintenance Parts List

Epson RC620 Manual

Product

Learn More

Legal