Dell Networking S4810–Open Networking(ON) Getting Started GuideRegulatory Model: S4810

About this Guide

Install the Hardware

Attaching the Mounting Brackets

Mounting the Chassis in a Rack or Cabinet

Important Points to Remember

Installing AC Power Supplies

Installing the SFP+ and QSFP+ Optics

AC Power

Technical Specifications

Dell Networking S4810 Getting Started Manual

Introduction

Cabling diagram

Dell recommended switch configuration

Configure route for OOB management port (optional)

Spanning tree

Save configuration

Configure Data Center Bridging (DCB) (Optional)

Apply policies to switch ports

Configure ETS values

Reverting from DCB to non-DCB configuration (Optional)

Revert to default VLAN ID on switch and arrays

Additional resources

Networking S4810

Revisions

hardware configuration

Configure spanning tree on edge ports

Configure DCB policies

Optional stack configuration

Configure stack on the second switch

Configure login credentials

additional resources

key features

ieee compliance

The S4810–ON System

Orderable S4810–ON Components

Features

Site Preparations

Rack Mounting

Storing Components

Install the S4810–ON

Installing the System into a Two-Post Rack or Cabinet

Attaching the Mounting Brackets into a Four-Post Rack or Cabinet

Installing the System into a Four-Post Rack or Cabinet

Attaching the Ground Cable

Remove the SFP+ and QSFP+ Optics

Connecting Two S4810–ON Systems

Power Up Sequence

DC Power

Power Supplies

Installing an AC or DC Power Supply

Components

Installing a Fan Module

Replacing a Fan Module

Console Ports

Access the RJ-45 Console Port with a DB-9 Adapter

Specifications

IEEE Standards

Japan: VCCI Compliance for Class A Equipment

Korean Certification of Compliance

Electromagnetic Compatibility (EMC)

Removing the SD Card

Replacing the Battery

Technical Support

Requesting a Hardware Replacement

Information Icons

CLI Basics

Obtaining Help

Navigating the CLI

Enabling Software Features on Devices Using a Command Option

feature vrf

Command Modes

dhcp mode

interface mode

lldp mode

monitor session mode

vrrp mode

File Management

HTTP Copy via CLI

copy

delete

format flash (S-Series)

fsck flash

rename

show boot system

show bootvar

show file-systems

show os-version

show running-config

show startup-config

show version

upgrade

Control and Monitoring

cam-acl

cam-acl-vlan

configure

disable

enable

enable optic-info-update interval

enable xfp-power-updates

exec-banner

exec-timeout

exit

ftp-server enable

ftp-server topdir

ftp-server username

hostname

ip http source-interface

ip ftp password

ip ftp source-interface

ip ftp username

ip telnet server enable

ip telnet server vrf

ip telnet source-interface

ip telnet vrf

ip tftp source-interface

line

motd-banner

ping

reload

send

service timestamps

show alarms

restore factory-defaults

show cam-acl-vlan

show command-history

show command-tree

show cpu-traffic-stats

Information Symbols and Warnings

Related Publications

Orderable S4810 Components

Ports

Site Selection

Cabinet Placement

Install the S4810 Chassis in a Rack or Cabinet

Install the System into a Two-Post Rack or Cabinet

Attach the Mounting Brackets into a Four-Post Rack or Cabinet

Install the System into a Four-Post Rack or Cabinet

Install the SFP+ and QSFP+ Optics

Splitting QSFP Ports to SFP+ Ports

Important Points to Know

Connect Two S4810 Systems

Connect Three S4810 Systems

Supply Power and Power Up the System

Hot-Swap Units in a Stack

Install an AC or DC Power Supply

Install a Fan Module

Access the RJ-45 Console Port (RS-232)

Chassis Physical Design

DC Power Requirements

USA Federal Communications Commission (FCC) Statement

Product Recycling and Disposal

SD Card Removal

Battery Replacement

The iSupport Website

Contacting the Technical Assistance Center

requesting a hardware replacement

Dell Networking S4810 Getting Started Manual

Product

Learn More

Legal


Contents Table Of Contents About this Guide Install the Hardware Attaching the Mounting Brackets Mounting the Chassis in a Rack or Cabinet Important Points to Remember Installing AC Power Supplies Installing the SFP+ and QSFP+ Optics AC Power Technical Specifications	Dell Networking S4810–Open Networking(ON) Getting Started GuideRegulatory Model: S4810 Next / 16