Craftsman SECURITY+ 139.53757 User Instructions

Also see for SECURITY+ 139.53757: User instructions

CRAFTSMANINSTALLATION1. Unplug the motor unit before proceeding.2. OPEN RECEIVER: Insert a small screwdriver in slot onreceiver front panel as shown. Twist up actuator cover.3. CONNECT RECEIVER AND MOTOR UNIT: Remove about1/4" of insulation from each end of the 2-strand bell wire.Connect one end to the receiver screw terminals (polarity isNOT required). Route wire along the channels and out thebottom as shown.4. Connect the other end of the bell wire to the two motor unitterminals labeled “2” (white) and “1” (red), “common” and“command” or the terminals used for the push button control.5. Use insulated staples to secure bell wire between receiverand motor unit. Length of bell wire depends on where thereceiver will be installed. Replace actuator cover.6. Choose a 120Vac polarized outlet for the receiver which isOUT OF THE REACH OF CHILDREN. Plug receiver intoselected outlet. Return power to the motor unit.PROGRAMMING THE REMOTE TO THE RECEIVERWith Security#®, the code between the remote control and thereceiver changes with each use, accessing over 100 billion newcodes.You can activate your motor unit with up to 8 Security*#® remotecontrols and one Security%*® Keyless Entry.1. Remove the front panel of receiver case. Re-connect powerto motor unit.2. Press and release the “SMART” actuator on the receiver. Thelearn indicator light will glow steadily for 30 seconds.3. Within 30 seconds, press and hold the button on thehand-held remote that you wish to operate your garage door.The motor unit will now operate when either the receiveractuator or the remote control push button is pressed.Repeat Steps 2 and 3 for each remote control that will be usedto operate the garage door motor unit.PROGRAMMING THE FINGERPRINT KEYLESS ENTRYTO THE RECEIVERNOTE: The unit must have an enrolled user before it can beprogrammed to the receiver. Due to the 30 second time interval,a second person may be needed to press the “SMART”actuator.1. Remove the front panel of the receiver case. Press andrelease the “SMART” actuator on the receiver. The “SMART”indicator light will glow steady for 30 seconds.2. Open the Fingerprint Keyless Entry cover and wait for ReadyLED to light.3. Within 30 seconds of pressing the “SMART” actuator, slowlyand firmly swipe enrolled finger.NOTE: The Retry LED will light if another swipe is needed.4. After a passed swipe the Pass LED will light followed by a litSend LED. Programming is complete.5. if the opener does not operate, press and release theResend button at 1 second intervals for up to 5 seconds untilthe door moves. Programming is complete.TO ERASE ALL REMOTE CONTROL CODESPress and hold the “SMART” actuator on the receiver panel untilthe indicator light turns off (about 6 seconds). All transmittercodes are now erased. Then follow the steps above toreprogram each remote control.SECURITYUniversal Receiver@) Model 139.53757USER INSTRUCTIONSTo prevent possible SERIOUS INJURY or DEATH fromelectrocution:° Be sure power is NOT connected BEFORE installing thereceiver.To prevent possible SERIOUS INJURY or DEATH from amoving gate or garage door:e Install door control within sight of gate or garage door, outof reach of children at a minimum height of 5 feet (1.5 m),and away from all moving parts of gate or door.e NEVER permit children to operate or play with door controlpush buttons or remote control transmitters.® Activate gate or door ONLY when it can be seen clearly, isproperly adjusted, and there are no obstructions to gate ordoor travel.¢ ALWAYS keep gate or garage door in sight until completelyclosed. NEVER permit anyone to cross path of moving gateor garage door.NOTICE TO U. S. CONSUMERS:Some states prohibit the service or repair of garage door motor unitswhich cannot be made to comply with the safety standards containedin UL 325 (1988 revision). In order to comply with both the letter andthe spirit of these laws, this universal remote control converter kitshould not be used with any Sears Craftsman® garage door openermanufactured prior to April 1, 1982.Power Indicator LighteT TyTerminalssaeSu—Actuator Cover__ Bell Wiref1]|PeeSMART‘OlyChannelsIndicator otNL?Light 2= OL Connect Bell Wireaa || To Garage DoorOpener Terminals"SMART"Actuator Bell WireFingerprint KeylessEntry ||3-Function . .Remote Control vniversay Receiver2S\ Selectapush buttonfortefolNOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications ofthis receiver and/or transmitter are prohibited, except for changing the code setting or replacingthe battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to thefollowing two conditions: (1) this device may not cause harmful interference, and (2) this devicemust accept any interference received, including interference that may cause undesiredoperation.To order replacement parts call:1-800-4-MY-HOME® (1-800-469-4663)

/ 2

Related manuals for Craftsman SECURITY+ 139.53757

Craftsman Security+ 139.53757 User Instructions

Craftsman UNIVERSAL RECEIVER 139.18152 User Instructions

Craftsman 139.18152 User Manual

This manual is suitable for:

SECURITY+ 139.53757

Craftsman SECURITY+ 139.53757 User Instructions

Product

Learn More

Legal