Menu
Craftsman 139.18152 User Manual
Also see for UNIVERSAL RECEIVER 139.18152: User instructions
 |
Universal ReceiverModel 139.18152USER INSTRUCTIONSNOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of thisreceiver and/or transmitter are prohibited, except for changing the code setting or replacing thebattery. THERE ARE NO OTHER USER SERVICEABLE PARTS.Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to thefollowing two conditions: (1) this device may not cause harmful interference, and (2) this devicemust accept any interference received, including interference that may cause undesired operation.NOTICE TO U. S. CONSUMERS:Some states prohibit the service or repair of garage door motor unitswhich cannot be made to comply with the safety standards contained inUL 325 (1988 revision). In order to comply with both the letter and thespirit of these laws, this universal remote control converter kit shouldnot be used with any Sears Craftsman ® garage door openermanufactured prior to April 1, 1982.INSTALLATION• Unplug the motor unit before proceeding.• OPEN RECEIVER: Insert a small screwdriver in slot onreceiver front panel as shown. Twist up actuator cover.• CONNECT RECEIVER AND MOTOR UNIT: Remove about1/4" of insulation from each end of the 2-strand bell wire.Connect one end to the receiver screw terminals (polarity isNOT required). Route wire along the channels and out thebottom as shown.• Connect the other end of the bell wire to the two motor unitterminals labeled “2” (white) and “1” (red), “common” and“command” or the terminals used for the push button control.• Use insulated staples to secure bell wire between receiver andmotor unit. Length of bell wire depends on where the receiverwill be installed. Replace actuator cover.• Choose a 120Vac polarized outlet for the receiver which isOUT OF THE REACH OF CHILDREN. Plug receiver intoselected outlet. Return power to the motor unit.Actuator Cover"SMART"IndicatorLight"SMART"ActuatorTerminalsBell WireChannelsConnect Bell WireTo Garage DoorOpener TerminalsBell WirePower Indicator LightUniversal Receiver"SMART"ActuatorIndicator Light3-Function Remote ControlSelect apush buttonPROGRAMMING THE REMOTE TOTHE RECEIVERWith Security✚®, the code between the remote control and thereceiver changes with each use, accessing over 100 billion newcodes.You can activate your motor unit with up to 8 Security✚® remotecontrols and one Security✚® Keyless Entry.1. Pry open the front panel of receiver case with a screwdriver.Re-connect power to motor unit.2. Press and release the “SMART” actuator on the receiver. Thelearn indicator light will glow steadily for 30 seconds.3. Within 30 seconds, press and hold the button on the hand-heldremote that you wish to operate your garage door.The motor unit will now operate when either the receiver actuatoror the remote control push button is pressed.Repeat Steps 2 and 3 for each remote control that will be used tooperate the garage door motor unit.TO ERASE ALL REMOTE CONTROL CODESPress and hold the “SMART” actuator on the receiver panel untilthe indicator light turns off (about 6 seconds). All transmitter codesare now erased. Then follow the steps above to reprogram eachremote control.To order replacement parts call...1-800-4-MY-HOME ® (1-800-469-4663)®To prevent possible SERIOUS INJURY or DEATH from electrocution:• Be sure power is not connected BEFORE installing door control.• Connect ONLY to 24 VOLT low voltage wires.To prevent possible SERIOUS INJURY or DEATH from a closing garagedoor:• Install door control within sight of garage door, out of reach ofchildren at a minimum height of 5 feet(1.5 m), and away from all moving parts of door.• NEVER permit children to operate or play with door control pushbuttons or remote control transmitters.• Activate door ONLY when it can be seen clearly, is properly adjusted,and there are no obstructions to door travel.• ALWAYS keep garage door in sight until completely closed. NEVERpermit anyone to cross path of closing garage door. |
Related manuals for Craftsman UNIVERSAL RECEIVER 139.18152
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved