Menu
Craftsman CMXZDCG440 Quick Manual
Also see for CMXZDCG440: User manual
    |
...the light bulb blinks 3 times.1 Press any programmed PIN, then press and holdthe * button until...+? ? ? ?PIN2+? ? ? ?Temporary PINEnter the temporary 4-digit PIN of yourchoice, then press the ENTER button.The light bulb will blink4 times.Then pressthe button.3+Press the numberof hours thetemporary PINwill work (up to 255).3OR Then pressthe # button.+Press the numberof openings thetemporary PINwill work (up to 255).1 blink 1 blinkTo test, press the temporaryPIN, then press the ENTERbutton. The garage door openerwill activate. If the temporaryPIN was set for a number ofopenings, the test will use upone opening.To clear the temporary PIN, repeat steps 1-3 above, setting the number of hours or openings to 0 in step 3.*Replace the battery when the keypadbecomes dim or does not light after a buttonis pressed.Dispose of old battery properly.SAVE THESE INSTRUCTIONS FORFUTURE REFERENCETo prevent possible SERIOUS INJURY or DEATH:• NEVER allow small children near batteries.• If battery is swallowed, immediately notify doctor.PROGRAM A TEMPORARY PINOPERATIONThe garage door opener activates when the PIN and ENTER button arepressed. The keypad will blink for 15 seconds, during that time theENTER button can be used to stop, start or reverse the door.If the wrong number is accidentally pressed, press the correct PIN thenthe ENTER button. The keypad will transmit only the last four digits thatwere pressed before the ENTER button.ONE BUTTON CLOSE: The keypad has a feature that allows the door to beclosed using the ENTER button instead of a PIN.NOTE: This feature is not available on garage door openers manufacturedprior to 2006 or an external receiver.To deactivate the one button close feature:1 Press and hold the 1 and 9 buttons for 10 seconds.2 The keypad will blink four times when the one button close feature isdeactivated.To activate the one button close feature:1 Press and hold the 1 and 9 buttons for 10 seconds.2 The keypad will blink twice when the one button close feature isactivated.REPLACEMENT PARTS9V Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10A25Keypad cover . . . . . . . . . . . . . . . . . . . . . . . . . . . 41D621Battery cover . . . . . . . . . . . . . . . . . . . . . . . . . . . 41D541NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications ofthis receiver and/or transmitter are prohibited, except for changing the code setting orreplacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.This device complies with Part 15 of the FCC rules and IC RSS-210. Operation is subject tothe following two conditions: (1) this device may not cause harmful interference, and (2) thisdevice must accept any interference received, including interference that may causeundesired operation.NOTE: This feature is not available on garage door openers that have agreen Learn button or an external receiver.A temporary 4-digit PIN can be programmed to allow access tovisitors. Each programmed PIN can program one temporary PIN. Thetemporary PIN can be set for a number of hours or a number of dooropenings. The temporary PIN cannot be the same as any previouslyprogrammed PIN.BATTERYINSTALLATION1 Select a location to mount the keypad at a minimum height of 5feet (1.5 m) out of the reach of children.2 Remove battery cover and battery.3 Mark the top mounting hole and drill 1/8 inch (3.2 mm) pilot hole.4 Install the top screw, allowing 1/8 inch (3.2 mm) to protrudeabove the surface. Position the keypad over the top screw.5 Mark the bottom hole and drill 1/8 inch (3.2 mm) pilot hole. Installthe bottom screw. Do not overtighten to avoid cracking the plastichousing.6 Reinstall battery and replace cover.9V BatteryCall: 888-331-4569www.craftsman.comNUMBER OF HOURS NUMBER OF OPENINGS |
Related manuals for Craftsman CMXZDCG440
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved