Menu
Craftsman CMXGLXT3200 Instruction Manual
                              |
8TOWINGWARNING: The log splitter is equipped with pneumatic tires, a Class I or abovecoupler (2 in. diameter ball required) and safety chains. Before towing, the safety chainsmust be secured to the hitch or bumper of the vehicle. Local regulations should bechecked regarding licensing, lights, towing, etc. Before towing, turn the fuel shut off valveon the engine to the “OFF” position. Failure to turn off the engine before towing may floodthe engine. Do not exceed 45 mph when towing the log splitter. Also see Towing Safetyon page 4 of this manual.MAINTENANCEShut off splitter and wait until it is completely cool before performingany maintenance. The log splitter should be on a level surface with wheels properlychocked before maneuvering on or around the log splitter.1) Consult the operating and maintenance instructions of the engine’s manufacturer forengine care and maintenance.2) Always check the oil level of the hydraulic reservoir before operation. Operating thelog splitter without an adequate oil supply will cause severe damage to the pump.3) Change the spin on filter after the first 25 hours of operation. There after change thespin on filter every 100 hours or seasonally, whichever comes first.4) To drain the hydraulic oil, remove the drain plug from the bottom of the tank. The drainplug is located just to the right of the oil filter.5) If the wedge needs to be sharpened, it can be removed and sharpened.6) Clean the breather cap after every 25 hours of operation. When operating in dustyconditions the breather cap should be cleaned more frequently. To clean, first removethe breather cap from the tank, then flush with solvent and blow out the cap with air.7) Also see General Repair and Maintenance Safety on page 3 of this manual.8) All replacement parts must meet manufacturer’s specifications.9) Grease Wheel Bearings and tighten all hardware seasonally.OPERATING INSTRUCTIONSWARNING:1. Clean the log splitter thoroughly before storage.Prepare the log splitter for storage at the end of the season or if the log splitter will notbe used for 30 days or more.STORING THE LOG SPLITTERWARNING: Never store the log splitter with fuel in the fuel tank inside of anybuilding where fumes could contact an open flame or spark, or whereignition sources are present, such as hot water and space heaters, furnaces,clothes dryers, stoves, electric motors, etc.NOTE: The use of pressure washers and/or garden hoses to clean the log splitter isNOT recommended. Using them to clean may cause damage to the bearings or theengine. In general, using water to clean the log splitter can shorten machine life andreduce serviceability.2. Wipe down the entire log splitter with an oiled rag to prevent rust, especially onthe push plate and the beam.3. Completely drain the fuel tank.WARNING: Never smoke while around or when handling fuel. Always drain fuelinto an approved container while outdoors and away from open flames and otherpotential sources of ignition. Be sure that engine is cool before draining the fuel.4. Start the engine and let it run until the fuel lines and carburetor are empty.5. Remove the spark plug. Holding a rag over the cylinder hole, pour approximatelya 1 ounce of engine oil into the cylinder and crank slowly to evenly distribute the oil.6. Replace the spark plug.7. Do not store and reuse gasoline from one season to another.8. Replace any gasoline can if it starts to rust. Using gasoline containing rust and/ordirt will cause operational problems for the log splitter.9. Always store the log splitter in a clean, dry area, preferably inside and safe fromweather. Do not store the log splitter close to any corrosive materials, such asfertilizer.NOTE: If storing the log splitter in an unventilated or metal storage shed, be certain torust-proof the equipment by coating with a light oil or silicone.VERTICAL POSITION1. Pull beam lock pin2. Rotate the beam in the uprightposition by lifting the beam.Upright position for splitting large logs.FOR VEHICLE TOWINGPress handle downand lock tightly.Rotate the SupportLeg to the up position.Hook safety chainsto towing vehicle.HORIZONTAL POSITION |
Related manuals for Craftsman CMXGLXT3200
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved