Menu
Craftsman CMXGLXT2700 Instruction Manual
                              |
STEP 1: Attach the Wheel1.1 Remove the nuts (73) and bolts (58) from the wheel axle.1.2 Insert the wheel into the wheel axle of the hydraulic reservoir, secure with thepreviously removed nuts and bolts using two 17mm wrenches.47) FIRE PREVENTION• ONLY refuel the log splitter in clear areas with no gas fumes and no spilled gas.• NEVER operate the log splitter near flames, sparks or smoke. Hydraulic oil and gasolineare flammable and potentially explosive.• NEVER add fuel while the engine is hot or running. Allow the engine to cool completelybefore refueling.• If gasoline spills, move the log splitter away from the area of the spill and avoid creatingany source of ignition.• ALWAYS securely replace the gas cap.• ALWAYS clean wood debris from the muffler area of the engine.• ALWAYS store gasoline in an appropriate, tightly sealed container. Store the gascontainer in a cool, dry place and away from any heat sources.8) IMPORTANT NOTE RE: SPEAK ARRESTER-REGULATION:As a precautionary measure against possible flying sparks, always have a Class B fireextinguisher on hand when operating the log splitter in dry areas. The log splitter isequipped with an internal combustion engine that generates heat and potential flyingsparks. Only use the log splitter on or near any unimproved, forest-covered, brush-coveredor grass-covered land if the engine’s exhaust system is equipped with a spark arrester incompliance with any applicable local or state laws. Spark arresters should be effectivelymaintained and serviced. In the state of California, a spark arrester is required by law andother states have similar laws. Federal laws will apply when operating the log splitter onfederal land. Always research and comply with applicable state, local and federal lawsand regulations. A spark arrester muffler is optional and available as an accessory at yournearest engine dealer9) TOWING SAFETY• NEVER carry cargo or wood on the log splitter.• NEVER allow anyone to sit or ride on the log splitter.• NEVER move the log splitter over hilly or uneven terrain without a tow vehicle and/oradequate help.• NEVER exceed weight capacity of ball or load limits of coupler.• NEVER exceed speeds of 45 mph when towing the log splitter. Towing the log splitterat speeds higher than 45 mph could result in loss of control, damage to the equipment,and/or serious injury or death. Adjust towing speeds for the terrain and conditions.Utilize extra caution when towing over rough terrain. Avoid large holes, sharp turnsand steep angles when towing the log splitter.• ALWAYS attach safety chains when towing the log splitter.• ALWAYS confirm coupler tightness every time before towing and after towing 50 miles.• ALWAYS use caution when backing up with the log splitter in tow as it could jackknife.• ALWAYS accommodate for the added length of the log splitter when turning, parking,crossing intersections and always when driving while towing the log splitter.• ALWAYS disconnect the log splitter from the towing vehicle before operating.• ALWAYS know and comply with all local and state regulations governing towing,licensing, and lights before towing the log splitter.• ALWAYS check before towing that the log splitter is correctly and securely attached tothe towing vehicle and that the safety chains are secured to the hitch or bumper of thevehicle with enough slack to allow for turning. Always use a Class I or above; 2” ballfor connecting to the log splitter.• ALWAYS replace damaged ball couplers.• ALWAYS turn the fuel shut off valve on the engine to the “OFF” position before towingthe log splitter. Failure to turn off the engine before towing may flood the engine anddamage engine oil.ASSEMBLY INSTRUCTIONS• Screwdriver• Hammer• Band Cutter• 13mm, 17mm and 19mm Wrenches• Large Adjustable WrenchTOOLS REQUIRED (Not Included)STEP 2: Attach Hydraulic Reservoir and Tow Bar Assembly2.1 Attach the tow bar assembly to the hydraulic reservoir and secure using M12x100hex bolts (23), Ø12 flat washers (63) and M12 nylon lock nuts (12) using two19mm wrenches.The log splitter is designed only for splitting wood. Using the log splitter for any otherpurpose can result in serious injury or death and may void the warranty.10) PERSONAL PROTECTIVE EQUIPMENTBEFORE operating the log splitter always be sure to put on appropriate safety gear,including eye protection (goggles), steel-toed shoes and tight-fitting gloves (without loosecuffs or draw strings). Also, the use of proper hearing protection (headphones) is requiredwhen operating the log splitter.WARNING: IMPORTANT SAFETY INFORMATIONNever use the log splitter for any purposes other than splitting wood.WARNING:6312237358 |
Related manuals for Craftsman CMXGLXT2700
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved