Menu
Craftsman CMCR001 Instruction Manual
Also see for CMCR001: Instruction manual
                                    |
5English WARNING: Burn hazard. Do not submerge thebattery pack in any liquid or allow any liquid toenter the battery pack. Never attempt to open thebattery pack for any reason. If the plastic housing ofthe battery pack breaks or cracks, return to a servicecenter for recycling. CAUTION: Burn hazard. To reduce the risk of injury,charge only CRAFTSMAN rechargeable battery packs.Other types of batteries may overheat and burstresulting in personal injury and property damage. CAUTION: Under certain conditions, with the chargerplugged into the power supply, the charger canbe shorted by foreign material. Foreign materialsof a conductive nature, such as, but not limited to,grinding dust, metal chips, steel wool, aluminumfoil or any buildup of metallic particles should bekept away from the charger cavities. Always unplugthe charger from the power supply when there is nobattery pack in the cavity. Unplug the charger beforeattempting to clean.Charging a BatterynOTE: To ensure maximum performance and life of lithium-ion battery packs, charge the battery pack fully beforefirst use.1. Plug the charger into an appropriate outlet beforeinserting battery pack.2. Connect the charger and battery pack, making surethe battery is fully seated. The (charging) light willblink continuously indicating that the charging processhas started.3. The completion of charge will be indicated by the lightremaining ON continuously. The battery pack is fullycharged and may be removed and used at this time orleft in the charger.nOTE: To remove the battery pack, some chargers requirethe battery pack release button to be pressed.IndicatorsChargingFully ChargedHot/Cold Pack DelayA charger will not charge a faulty battery pack. The chargerrefusing to light could indicate a problem with the charger.nOTE: If the charger refuses to light, take the charger andbattery pack to be tested at an authorized service center.hot/Cold Pack DelayWhen the charger detects a battery pack that is too hotor too cold, it automatically starts a Hot/Cold Pack Delay,suspending charging until the battery pack has reached anappropriate temperature. The charger then automaticallyswitches to the pack charging mode. This feature ensuresmaximum battery pack life.A cold battery pack may charge at a slower rate than awarm battery pack.Important Charging Notes1. Longest life and best performance can be obtained ifthe battery pack is charged when the air temperatureis between 65 °F – 75 °F (18 ° – 24 °C). DO NOT chargewhen the battery pack is below +40 °F (+4.5 °C), orabove +104 °F (+40 °C). This is important and willprevent serious damage to the battery pack.2. The charger and battery pack may become warm to thetouch while charging. This is a normal condition, anddoes not indicate a problem. To facilitate the cooling ofthe battery pack after use, avoid placing the charger orbattery pack in a warm environment such as in a metalshed or an uninsulated trailer.3. If the battery pack does not charge properly:a. Check operation of receptacle by plugging in a lampor other appliance;b. Check to see if receptacle is connected to a lightswitch which turns power off when you turn outthe lights;c. Move the charger and battery pack to a locationwhere the surrounding air temperature isapproximately 65 °F – 75 °F (18 ° – 24 °C);d. If charging problems persist, take the tool, batterypack and charger to your local service center.4. The battery pack should be recharged when it fails toproduce sufficient power on jobs which were easilydone previously. DO NOT CONTINUE to use under theseconditions. Follow the charging procedure. You mayalso charge a partially used pack whenever you desirewith no adverse effect on the battery pack.5. Foreign materials of a conductive nature such as, butnot limited to, grinding dust, metal chips, steel wool,aluminum foil, or any buildup of metallic particlesshould be kept away from charger cavities. Alwaysunplug the charger from the power supply when thereis no battery pack in the cavity. Unplug the chargerbefore attempting to clean.6. Do not freeze or immerse the charger in water or anyother liquid.Charger Cleaning Instructions WARNING: Shock hazard. Disconnect the chargerfrom the AC outlet before cleaning. Dirt and greasemay be removed from the exterior of the charger usinga cloth or soft non-metallic brush. Do not use water orany cleaning solutions.Wall MountingThese chargers are designed to be wall mountable or tosit upright on a table or work surface. If wall mounting,locate the charger within reach of an electrical outlet,and away from a corner or other obstructions which mayimpede air flow. Use the back of the charger as a templatefor the location of the mounting screws on the wall. Mountthe charger securely using drywall screws (purchasedseparately) at least 1" (25.4 mm) long, with a screw headdiameter of 0.28–0.35" (7–9 mm), screwed into wood to an |
Related manuals for Craftsman CMCR001
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved