OneStart

Menu
Craftsman 247 Owner's Manual Manual pdf 24 page image

Craftsman 247 Owner's Manual

Also see for 247: Operator's manual

Page 1 previewPage 2 previewPage 3 previewPage 4 previewPage 5 previewPage 6 previewPage 7 previewPage 8 previewPage 9 previewPage 10 previewPage 11 previewPage 12 previewPage 13 previewPage 14 previewPage 15 previewPage 16 previewPage 17 previewPage 18 previewPage 19 previewPage 20 previewPage 21 previewPage 22 previewPage 23 previewPage 24 previewPage 25 previewPage 26 previewPage 27 previewPage 28 previewPage 29 previewPage 30 previewPage 31 previewPage 32 previewPage 33 previewPage 34 previewPage 35 previewPage 36 previewPage 37 previewPage 38 previewPage 39 previewPage 40 previewPage 41 previewPage 42 previewPage 43 previewPage 44 previewPage 45 previewPage 46 previewPage 47 previewPage 48 previewPage 49 previewPage 50 previewPage 51 previewPage 52 previewPage 53 previewPage 54 previewPage 55 previewPage 56 previewPage 57 previewPage 58 previewPage 59 previewPage 60 previewPage 61 previewPage 62 previewPage 63 previewPage 64 preview
Craftsman 247 Owner's Manual Manual pdf 24 page image
Trouble PossibleCause RemedialActionEnginefailstostart 1. Blade control lever engaged.2. Parking brake not engaged.3. Spark plug wire(s) disconnected.4. Choke not activated5. Fuel tank empty, or stale fuel.6. Blocked fuel line.7. Faulty spark plug.1. Disengage blade control lever2. Engage parking brake.3. Connect wire(s) to spark plug.4. Pull out the CHOKE control5. Fill tank with clean, fresh gasoline.6. Clean fuel line or replace fuel filter7. Clean, adjust gap or replace spark plug.Engine runs erratic 1. Unit running with CHOKE applied. 1. Push CHOKE control in.2. Spark plug wire loose. 2. Connect and tighten spark plug wire.3. Blocked fuel line or stale fuel. 3. Clean fuel line; fill tank with fresh gasoline.4. Vent in gas cap plugged. 4. Clear vent or replace cap if damaged.5. Water or dirt in fuel system. 5. Drain fuel tank. Refill with fresh gasoline.Engine overheats 1. Engine oil level low. 1. Fill crankcase with correct oil.2. Air flow restricted. 2. Clean grass clippings and debris fromaround the engine's cooling fins andblower housing.Engine hesitates at 1. Spark plug gap too close. 1. Remove spark plug end reset the gaphigh RPM to.030".Idles poorly 1. Spark plug fouled, faulty or gap too wide. 1. Replace spark plug. Set plug gap to.030".Excessive vibration 1. Cutting blade loose or unbalanced, i 1. Tighten blade and spindle. Balance blade.2. Damaged or bent cutting blade. 2. Replace blade.Mower will not mulch 1. Wet grass. 1. Wait until grass is dry to cut.grass 2. Excessively high grass. 2. Mow once at a high cutting height, thenmow again at desired height or make anarrower cutting swath.3. Dull blade. 3. Sharpen or replace blade.Uneven cut 1. Deck not balanced properly. 1. Level the deck side to side.2. Dull blade. 2. Sharpen or replace blade.3. Uneven til'e pressure. 3. Check tire pressure in all four tires.NOTE: Suggestions listed hero are only for minor repairs, ff the problem is not resolved, or for anyproblems not mentioned here, please contact Sears service by calling 1-800-4-MY-HOME®.24
/ 64
Related manuals for Craftsman 247
Craftsman 220 User Manual first page preview
Craftsman 220 User Manual
Craftsman 123.24201 User Manual first page preview
Craftsman 123.24201 User Manual
Craftsman ZTS 7500 Operator's Manual first page preview
Craftsman ZTS 7500 Operator's Manual
This manual is suitable for:
247247.270250250270
Product
Menu
Learn More
Menu
Legal
Menu
Copyright © 2024 OneStart. All Rights Reserved