Menu
Craftsman 171.254841 Owner's Manual
                                                        |
FIGURE 13\,/NOTE ORIENTATION OF,O GROOVE IN FENCESURFACE OF FENCE GUfDE " \, GUIDEMUST BE FLUSH WITH _ \_BACK SURFACE OF ROUTER ' '_ FENCE GUIDETABLE FENCE_'10 32 HEX 'KEPS NUTFIGURE 14b-- RCLTE q--- "P:i / FENCE4. To align the fence, position the fence on the routertable so that the fence guide fits in the channels inthe top of the table, as shown in Figure 14a.5. Insert a 1/4-20 x 1-3/4" long round headsquare neck bolt, from the underside of thetable, through the slot in the fence, as shown inFigure 14a.FIGURE 14aF El'ICE C L_ !,lPrNOKNOB9,32 :D X34OD Xll£ _321D X34OD Xt:6TH!CK WASHER THICK WASHER",, X, \ 'E:U'DEJ 11" SCREWSCHANNEL 1544 20 X 13 4- LONG ROUND ROUTER TABLE '_\HEAD SQUARE NECK BOLT xi 4 2c x t 3 4 LONG ROUNDHEAD SQUARE NECK BOLT6. Place a 9/32" !.D. x 3/4" O.D. x 1/16" thick washerover the bolt, as shown in Figure 14a.7. Lightly thread a fence clamping knob onto the bolt.DO NOT TIGHTEN clamping knob at this time --fence must be able to MOVE FREELY from front toback on the table.8. Repeat Steps 5 through 7 for the other side of thefence.9. Make sure that the adjustable jointing fence isinside the router table fence as far as it will go andthat the clamping knob has been securely tightened•10. Line up the front of the fence with the "0" markson the top of the router table, as shown in Figure 14b.11. TIGHTEN the fence clamping knobs MAKINGSURE THAT THE FENCE DOES N©T MOVE.12. TIGHTEN the two #10-32 x 7/8" long panheadscrews to secure the fence guide to the fence, asshown in Figure 14a.13. Remove the fence from the table by unthreadingthe fence clamping knobs from the 1/4-20 x 1-3/4"long round head square neck bolts while holding thebolts in place from the underside of the table.14. Remove the 9!32" I.D. x 3/4" O.D. x 1/16" thickwashers from the bolts and then remove the bolts.15. Store fasteners in a cor:venient place so theycan be used at later time.16. Assemble the overhead guard to the router tablefence using two 14" pushnLts and the 1/4" O,D. x2-11/16" long overhead guard pivot pin, as shown inFigure 15:FIGURE 15OVERHEAD GUARDPP,IOT PIN-- D'.ERHEAD GL'_=D• 4 PUSHNUT--tl_ '_'_ ROUTER TABLEROUTER TABLE FENCE--a. Press one of the pushnuts onto one end of thepivot pin. (It will be necessary to tap the pushnutonto the overhead guard pivot pin with a hammerwhile supporting the other end of the overheadguard pivot pin.)b. Position the overhead guard on the fence sothe holes in the overhead guard line up with thethrough-hole in the router table fence• MAKESURE THE ORIENTATION OF OVERHEADGUARD ISAS SHOWN IN FIGURE 15.c. Insert the overhead guard pivot pin through thealigning holes.12 |
Related manuals for Craftsman 171.254841
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved