Menu
Craftsman 139.53758 Owner's Manual
  |
,.odei 139.537583-Function Mini Transmitter Owners ManualEC;,.O.rules prohibit adjustments to or modification of receiver and/or transmitter circuitry except for changing the code settingand replacing transmitter battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.Manufactured under 1 or more of the following US. patents: RE29,525; 4,037,201;4,750,118; 4.806,930i,ll ii ,iMATCH THE CODE IN NEW AND EXISTING TRANSMITTERSRemove the cover screw in NEW transmitter. Turn case over to access code switches #1 through #9. Be careful notto move circuit board components. Locate code switches in c_iginal transmitter(s), (Refer to illustration)_ Set code switchesin the 3_Function Mini Transmitter to the same positions as code switches in the original transmitter.NOTE 1: Code switches #2 through #g in ALL transmitters used to operate a receiver must be sot to match. (Codaswitch #1 on 8 3-function transmitter Is neutral. Set it to ANY position. It will not affect the code selected.NOTE 2: If the original transmltter(s) has only 7 or 8 code switches, set code switches #8 and!or #9 to center(0) position tn new transmitter.o-_JJ "0' "1 St_,ndard [I3-Function 0:3 -.,_ StandardiI" 1 €2-9)REPLACEMENT PARTS: Transmitter Housing Only (No circuit board) - 4tA3592; 12V Battery - 10A14CHANGE THE CODE IN RECEIVER AND TRANSMITTER(S)53000SR SERIES0NITH RECEIVER 'SR' CODE BUTTON)Garage Door Openers and Light Controls(illustration A shows a garage door opener receiver)Selec_ a traz_rni_efpushbuttonIo Xoperatereceiver _ t_ wffr °u_ _LKey Ring Push _ltonsHolder "S_' Indicator ....CodeButton LightMake sure all transmitters are set to matching code switchpositions as described above.1o Press the 'SR' code button on your receiver (illt_tra-tion A). The indicator light wilt turn ONe2. STAND AWAY FROM DOOR and press the transmit-ter's SELECTED PUSH BUTTON. The indicator lightwill turn OFF and door will move.Code in receiver nowmatches transmitter(s) code and will activate when theselected transmitter push button is pressed,NOTE: I! transmitter push button ts not pressedwithin 30 seconds, the Indicator light will turn OFF.Repeat 1 and 2,To use the 3-Function Mtnl Transmitter with other53000SR Serlse receivers: Select another transmitterpush button to operate e Light Control or additional garagedoor opener. Make sure all transmitters used to operatereceiver are set to the same cote (as described above).Then repeal I and 2.You can select a different transmitter push button to oper-ate each device.53000 SERIES(WITH RECEIVER CODE SWITCHES)Garage Door Openers and Light Controls(illustration B shows a garage door opener receiver)Push(_ulton Select atransmitter_ PushButton pushbuttonf _ J (+)Key Ring Push Button to operateg Holder (O) receiverI F_D WHT BLK Y_:Lcodeswitch#11 2 3 4 _;6 7 8 ii to positJortthe!!ltltlMltl pushbur_onCodeSwitch#1Make sure all transmitters are set to matching code switchpositionsas described above.1, Select a transmitterpush buttonto operatethe receiveras shown in Figure 13.2, Set RECEIVER code switch #1 to match the positionof the transmitter push button selected. Refer toillustration BeThen set remaining code switches inreceiver to match the transmitter(s) code switchpositions.NOTE: If the receiver has only 7 or 8 switches, sottransmitter switch #8 and/or #g to (0).To use the 3-FuncttonMlnl Transmitterwith other 53000Series receivers: Set receiver code switch #1 to matchthe positionof anothertransmitter push button. Then setremaining code switches to match transmitter(s) codeswitches,Code switches #2 through #9 in all transmitters usedto operate the receiver MUST be set to matchingpositions.IJIIL,I,ll,_,Jll,llJ_Ui© 19g0, Sears Roebuck & Company114Al160 _._ All RlghfJi Reserved Printed In Mexico |
Related manuals for Craftsman 139.53758
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved