Craftsman 113.22521 Owner's Manual

unpackingCONTENTSUNPACKING AND CHECKING CONTENTS ..... 6ASSEMBLY .................................... 7Mounting Belt and Disc Sander OnRecommended Craftsman Floor Base ........ 7Check Motor Rotation .......................... 11On-Off Switch .............................. 13Installing Work Table ....................... 15Installing Abrasive Belt-Tensioning and Tracking 16Installing Belt Dust Trap ..................... 17Installing Backstop .............................. 18GETTING TO KNOW YOUR SANDER ............ 18Belt Adjusting Screws .......................... 19Belt Locking Screws ......................... 19Work Table Tilt Lock Screw .................... 19Backstop Lock Screw ............................ 20Your Belt and Disc Sander is shipped complete inone carton (without motor or floor base)Separate all parts from packing materials and checkeach item with illustration and "Table of LooseParts." Make certain all items are accounted for,before discarding any packing materialIf any parts are missing, do not attempt to assemblethe Belt and Disc Sander, plug in time power cord,or turn the switch on until the missing parts areobtained and installed correctlyUsing a 1/2" wrench• remove the plywood attachedto time machine Save the nuts and bolts and washersYou will need them for attaching the machine tothe base1918and checking contentsBelt Table Locldng Bolts ....................... 20Belt Table Stop ......................... 20BASIC OPERATION ............................. 21Surface Finishing on the Belt ................. 21End Finishing on the Belt ................ 21Finishing Curved Edges on the Belt .............. 22Finishing Small End Surfacesand Curved Edges on the Disc ............. 22MAINTENANCE ......................... 23Wiring Diagram ...................... 23LUBRICATION ....................... 23TROUBLE SHOOTING ............................ 24Recommended Accessories ................. 24REPAIR PARTS ................................. 25PARTS LIST ..................................... 27°_ _"_°_--° TOOLS NEEDED ==========1/2"" Wrench __W16"' Wrench3/4' Wrench Medium ScrewdriverCOMBINATION SQUARE MUST BE TRUEDRAW LIGHTLINE ON BOARDALONG THISTRAIGHT EDGE OFBOARD 3/4" TH{CKTH_S EDGE MUST BEPERFECTLY STRAIGHTSHOULD BE NO GAP OR OVERLAP HERE WHENSQUARE IS FLIPPED OVER IN DOTTED POSITION2"r/ .. 3 517 \ ......111 114 Z ""-,16/' " .......L 2"'_KeyNo12345678910111213141516Table o1 Loose Parts OtyV-Beh 1/2x4!Backstol: 1Belt, Dust Trap . 1Motor Pul ev Belt Guard ]Belt Guard Suoport .3elt Guard SUDDOrt Bracket'S" Clip . 3Pan Head Screw. Type 23. 10-32 x 1/2 3Screw Pan Head Machine 1/4-20 x 1/2 2LockwasheL 1/4- 2Switch Assembly iSwitch Keys 2Baseand Belt Table (w/Sanding Belt) IDisc Dust TraD IDust Trap Cover lWork Table IKeyNo17iii IBTable of Loose Farts QtyBag (containing the following looseparts)Motor Pulley, 2 In Din ........ 1Wrench, 1 I2" ............. 25/32 Setscrew Wrench ......... 1Flat Head Machine Screw 10-32 x1-3/4 ................. 4Pan Head Screw, Type 23 8-32 x3/8 ............... 5Flat Washer 21/64 x 7/8 x 1/8 1Hex. Head Machine Screw5/16-18 x 1 ........... 1Screw MPan Hd. 10-32x9/16 1Lockwasher No 10 I nt Tooth 1Hange{, Cable ........ 1Owner's Manual ............ 1Sanding Disc (w/Set Screw) ........ 16