Canon imageFORMULA DR-3080CII Easy Start Manual

Also see for 3080CII - DR - Document Scanner: Startup manual

Contents

Canon imageFORMULA DR-3080CII Easy Start Manual Manual pdf 2 page image

☞Continued from front side1. Launch CapturePerfect 3.0 from the Programs menu in Windows.2. Select [Select Scanner] from the Scan menu.The Scanner Selection dialog box appears.3. Select [Canon DR-3080CII] and click [OK].1. When connecting the scanner with a SCSI cable, turn your computer OFF.2. Make sure the scanner’s power switch is in the OFF position.If the power switch is in the ON position, press the switch to turn it to the OFFposition.Power SwitchOFF Position ON Position3. Plug the power cord into the power connector on the rear of the scanner (11111).4. Plug the power cord into the power outlet (22222).5. When connecting the scanner with a USB cable, use the supplied USB cable.Type BType AInsert the plug with the mark facing down.6. Follow the steps below when connecting the scanner to your computer with aSCSI cable.6-1 Turn OFF your computer.Connecting the Scanner to Your PCThe scanner can be connected to a computer in two ways: by USB connection to astandard USB port on the computer, or by SCSI connection to a SCSI card installed inone of the computer’s expansion slots. Select a connection method appropriate toyour computing environment.Power ConnectorSCSI Connector(Half-pitch 50-pin, pin-type)USB ConnectorSCSI ID Dip SwitchesTurning On the Power (ScannerRecognition)When you turn on the DR-3080CII in a Windows 98SE/Me/2000/XP environment, Windowsuses the Plug and Play feature to recognize the scanner and automatically installs the neces-sary driver. (Windows NT does not have a scanner recognition feature.)❏ Windows NT does not support the USB interface. Use a SCSI connection withWindows NT.❏ Do not use both a USB connection and a SCSI connection at the same time.❏ Use only the supplied power cord.❏ Connect the scanner to your computer while the scanner is turned OFF.❏ Before connecting the scanner with a SCSI cable, turn your computer OFF.❏ A SCSI cable is not supplied. Acquire a SCSI cable beforehand that matchesthe shape of the connectors on your SCSI card and the scanner.The setup is now completeThis completes the setup of the DR-3080CII. Details on how to use the DR-3080CII aredescribed in the User’s Guide packaged with the scanner. Before you start using thescanner, make sure to thoroughly read the User’s Guide.Warning6-2 Connect the scanner to your computer with the SCSI cable.❏ When using the scanner in a daisy chain connection with other SCSI devices,pay attention to the following points:● The default setting for the SCSI ID is “SCSI ID=2.” Set the dip switches sothat the scanner’s SCSI ID is different from all other SCSI devices on thechain.1ON2OFFDip SwitchesDefault Position (SCSI ID=2)● The scanner has a built-in SCSI terminator that is permanently set to [ON].When using the scanner in a daisy chain connection, make sure that it isconnected as the terminating device and that the terminators of all otherSCSI devices in the chain have been set to [OFF].WarningThe scanner is now connected to your computer.Next, you need to turn on the scanner and ensure Windows recognizesit. (☞STEP5)Warning❏ When the scanner is connected by a SCSI cable, always turn on the scannerbefore the computer. Turning on the computer first may prevent it from recog-nizing the scanner properly.❏ Be sure to log on with Administrator privileges when logging on to WindowsNT/2000/XP.❏ Wait at least 10 seconds before turning the scanner on again after turning itoff.❏ If the scanner will not be used for an extended period, be sure to unplug itfrom the power outlet for safety.1. Check the connection between the scanner and the computer.2. Press the power switch to turn the scanner ON (when connecting by SCSI).The power indicator and start key indicator both light green.3. Turn ON your computer.On PositionPower indicator Power Switch4. Windows recognizes the DR-3080CII as new hardware and performs installationautomatically.(Windows98/Me/2000)(WindowsXP)Note● For Windows XP, a balloon help pop-up appears when installation is finished.● The installation finished message does not appear in Windows 98SE/Me/2000.● The scanner is registered on the computer as “CANON DR-3080CII USB” (or“CANON DR-3080CII SCSI”) in the “Imaging Device” directory of the DeviceManager.● When you restart your computer, the scan panel icon remains resident in the tasktray. For details, refer to “About the scan panel” on page 35 of the User’s Guide.Selecting the ScannerYou must select your scanner before using it with an ISIS- or TWAIN-compatible scanningapplication.The menus and procedures for selecting the scanner are different for each application.For details, refer to the manual for your scanning application when selecting the scanner.This section explains the procedure for selecting the scanner with “CapturePerfect 3.0”.For details on how to use CapturePerfect 3.0, refer to the “CapturePerfect 3.0 OperationGuide” in the Programs menu of Windows.The scanner is now correctly recognized by your computer.Next, you need to select the scanner with the scanning software.(☞STEP6)Scan Panel

/ 2

Related manuals for Canon 3080CII - DR - Document Scanner