OneStart

Menu
Bosch DIVAR IP 7000 1U Installation Manual Manual pdf 25 page image

Bosch DIVAR IP 7000 1U Installation Manual

Also see for DIVAR IP 7000 1U: Quick installation guide

Page 1 previewPage 2 previewPage 3 previewPage 4 previewPage 5 previewPage 6 previewPage 7 previewPage 8 previewPage 9 previewPage 10 previewPage 11 previewPage 12 previewPage 13 previewPage 14 previewPage 15 previewPage 16 previewPage 17 previewPage 18 previewPage 19 previewPage 20 previewPage 21 previewPage 22 previewPage 23 previewPage 24 previewPage 25 previewPage 26 previewPage 27 previewPage 28 previewPage 29 previewPage 30 previewPage 31 previewPage 32 previewPage 33 previewPage 34 previewPage 35 previewPage 36 previewPage 37 previewPage 38 previewPage 39 previewPage 40 previewPage 41 previewPage 42 preview
Contents
  1. Table Of Contents
  2. Table Of Contents
  3. Safety precautions
  4. Electrical safety precautions
  5. ESD precautions
  6. Important notices
  7. System overview
  8. Backplane
  9. Control panel buttons
  10. Power supply LEDs and overheat indicators
  11. Inserting hard disks
  12. Rack installation
  13. General system precautions
  14. Rack mounting instructions
  15. Installing the inner rails
  16. Installing the outer rails to the rack
  17. Installing the chassis into the rack
  18. Installing the chassis into a Telco rack
  19. System setup - first steps
  20. Using Bosch VMS Config Wizard
  21. Adding additional licenses
  22. Installing additional drives
  23. Adding and formatting the VHD as a VRM target
  24. Connecting to the internet
  25. Installing an Enterprise Management Server
  26. Recovering the unit
  27. Additional documentation and client software
  28. Appendices
  29. Motherboard component overview
  30. Motherboard features
  31. Block diagram
  32. PC health monitoring
  33. Power supply
  34. Overview of the Nuvoton BMC controller
Bosch DIVAR IP 7000 1U Installation Manual Manual pdf 25 page image
Installing additional drivesAfter physical drive mounting has been performed, the following configurations must beperformed for the drives to be accessible to both the operating system and Bosch VideoRecording Manager (VRM).– Adding new drives to Windows Server– Creating a VHD iSCSI target for VRM– Adding and formatting the VHD as a VRM targetSee also:– Inserting hard disks, page 13– Adding new drives to Windows Server, page 25– Creating a VHD iSCSI target for VRM, page 25– Adding and formatting the VHD as a VRM target, page 26Adding new drives to Windows ServerTo add new drives to Windows server:1. On the Bosch VMS default screen, press CTRL+ALT+DEL, then hold down SHIFT whileclicking the Switch User option and keep SHIFT pressed for about five seconds.Note: To perform administrative tasks, the BVRAdmin account can be entered2. In the taskbar, click Server Manager. The Server Manager window is displayed.3. In the left pane, expand Storage, then click Disk Management.The added hard drisk appear as Unallocated.4. Right-click the Unallocated disk, then click New Simple Volume.The New Simple Volume Wizard dialog box is displayed.5. In the Welcome dialog box, click Next.6. In the Specify Volume Size dialog box, allow all of the automatically allocated space andclick Next.7. In the Assign Drive Letter or Path dialog box, click Assign the following drive letter,enter the drive letter assigned to the new drive, then click Next.8. In the Format Partition dialog box make sure the following settings are correct, then clickNext.– File system: NTFS– Allocation unit size: Default– Volume label: New Volume– The Perform a quick format check box must be selected.9. In the Summary dialog box, click Finish.The description of the new drive changes to Healthy (Primary Partition).Creating a VHD iSCSI target for VRMTo create a VHD iSCSI target for VRM:1. On the Bosch VMS default screen, press CTRL+ALT+DEL, then hold down SHIFT whileclicking the Switch User option and keep SHIFT pressed for about five seconds.Note: To perform administrative tasks, the BVRAdmin account can be entered2. In the taskbar, expand Microsoft iSCSI Software Target, expand iSCSI Targets, thenclick the TG0 icon.All existing virtual disks are displayed with their LUN numbers.3. Right-click the TG0 icon, then click Create Virtual Disk for iSCSI Target.The Create Virtual Disk Wizard dialog box is displayed.4. I n the Welcome dialog box, click Next.66.16.2DIVAR IP 7000 1U Installing additional drives | en 25Bosch Sicherheitssysteme GmbH Installation Manual 2014.12 | V3 | DOC
/ 42
This manual is suitable for:
DIVAR IP 7000 1U
Product
Menu
Learn More
Menu
Legal
Menu
Copyright © 2024 OneStart. All Rights Reserved