Bosch CSG7364B1 User Manual And Installation Instructions

Also see for 8 Series: Instruction manual Recipes Instruction manual Installation instructions Assembly instructions

Descaling en3119.2 Cleaning the cooking compartmentafter using the cleaning aidATTENTION!The prolonged presence of moisture in the cookingcompartment leads to corrosion.▶ After using the cleaning assistance, wipe the cook-ing compartment and allow it to dry completely.1. Allow the appliance to cool down.2. Wipe out the remaining water in the cooking com-partment using an absorbent sponge cloth.3. Clean the smooth enamel surfaces in the cookingcompartment with a dish cloth or a soft brush. Re-move stubborn food remnants using a stainlesssteel scouring pad.4. Remove limescale with a cloth soaked in vinegar,and wipe this away with clean water.5. Dry the cooking compartment with a soft cloth.6. To dry the cooking compartment completely, leavethe appliance door open for approx. 1 hour or usethe drying function.→ "Setting the drying process", Page 32Descaling20 DescalingRegular descaling is necessary to ensure that yourappliance continues to operate correctly.How frequently you need to run the descaling pro-gramme depends on the water hardness and howmany times you have used the steam-assisted opera-tions. The appliance indicates when only another 5 orfewer steam-assisted operations are possible. If you donot carry out descaling, you can no longer set any op-eration with steam.Descaling comprises several steps and takesapproximately 70 - 95 minutes:¡ Descaling (approx. 55 - 70 minutes)¡ First rinse cycle (approx. 8 - 12 minutes)¡ Second rinse cycle (approx. 8 - 12 minutes)For reasons of hygiene, the descaling programme mustbe run in full.If descaling is interrupted, you can no longer set anyoperation. To ensure that the appliance is ready for op-eration again, carry out 2 rinse cycles.20.1 Preparing descalingATTENTION!The length of time for which the descaler is left to workis based on the recommended, liquid descaler. Otherdescalers may damage the appliance.▶ Only use the liquid descaler recommended by usfor the descaling programme.If descaling solution comes into contact with the controlpanel or other delicate surfaces, it will damage them.▶ Remove descaling solution immediately with water.1. Mix the descaling solution:‒ 200 ml liquid descaler‒ 400 ml water2. Open the control panel.3. Remove the water tank and fill it with descaling solu-tion.4. Once the descaling solution has been poured intothe water tank, slide the tank back in.5. Close the control panel.20.2 Setting the descaling programmeRequirement: → "Preparing descaling", Page 311. Press "Cleaning" in the menu.2. Press "Descaling".The duration cannot be changed.3. Press .a A notification stating that you should carry out thenecessary preparatory work for descaling appearson the display.4. Confirm the message.a The descaling programme starts and the durationcounts down.a Once the first part of the descaling programme hasfinished, a signal tone sounds. The applianceprompts you to rinse twice.5. To rinse the appliance, for each rinse cycle:‒ Open the control panel and remove the watertank.‒ Thoroughly rinse the water tank and fill it withfresh water.‒ Slide in the water tank and close the controlpanel.a A signal tone sounds when each rinse cycle hasended.6. Once the second rinse cycle is complete:‒ Empty and dry the water tank.→ "Emptying the water tank", Page 19‒ Press to switch the appliance off.Drying21 DryingTo prevent residual moisture , dry the cooking compart-ment following operation with steam and after using thecleaning aid.ATTENTION!If there is water on the cooking compartment floorwhen operating the appliance at temperatures above120 °C, this will damage the enamel.▶ Do not use the appliance if there is water on thecooking compartment floor.▶ Wipe away any water on the cooking compartmentfloor before operation.