Menu
Black & Decker Workmate 225 Type 3 Instruction Manual
Also see for Workmate 225 Type 3: Instruction manual
  |
WWWW oooo rrrr kkkk mmmm aaaa tttt eeee 2222 2222 5555 TTTT yyyy pppp eeee 3333IMPORTANT SAFETY INSTRUCTIONS1. Do not load with more than 450 pounds.2. Do not apply an unbalanced load which could cause the work center totip over.3. Do not use the work center as a stepladder or standing platform. Donot use the lower platform as a step when the work center is in“Workbench” position. The footboard is a foot REST only.4. Do not store work center outdooors or in a damp location.5. Avoid applying excessive force when clamping with the swivel pegs.6. Be sure that the legs are fully open (for workbench height) and be surethat the table locks in position.7. When using a power tool with the work center, follow the safetyinstructions in the tool’s instruction manual.8. Always wear safety glasses when operating power tools.9. An even pressure of the vise jaws on the workpiece is essential. Tightenboth crank handles uniformly.SAVE THIS MANUAL FOR FUTURE REFERENCEASSEMBLY:The Workmate® 225 Type 3 work center comes partially assembled. Astandard hammer is required for assembly. A plastic socket wrench isincluded. Empty the contents of the box and identify all components(see Figure 1). Place the frame (A) on the floor in the position shown inFigure 1. Find the release levers near the front rubber feet on the sides ofthe frame. Depress both release levers as shown in Figure 2 and pull upuntil you hear the frame lock in place.VISE JAW BRACKET:1. Select the vise screws (D) and the pivot nuts (E). Screw one pivot nutonto each vise screw about halfway, as shown in Figure 3.2. Insert the unthreaded end of the vise screws into the frame such that thepivot nuts are located in the slots on the top of the frame and theunthreaded ends protrude through the holes in the front of the frame, asshown in Figures 3 and 4.3. Install the two vise cranks (F) and secure them by driving the pins (N)through the holes in the cranks and the vise screws. (Align the holes inthe vise cranks with the holes in the vise screws and strike the pinssharply with a steel hammer until they are flush with the sides of the visecranks.) See Figure 5.4. Closely examine the two front top blocks and the two rear ones. Notethat the front blocks do not have a protruding tab on the bottom sidewhere the rear blocks do. Select the front vise jaw, (B), and the two fronttop blocks, (K). Place the top blocks on the rails of the frame as shownin Figure 6.5. Install the front vise jaw on top of the top blocks so that the small holesat each end of the jaw fit down over the posts on the top side of theblocks. With the jaw positioned as described above insert into the frameas shown in Figure 6, insert two of the four bolts, (M) into the holes inthe jaw and tighten them securely into the holes in the pivot nut. Use thesocket wrench, (J) provided, shown in Figure 1.NOTE: For clarity, only the left side assembly is shown. Perform alloperations on right side as well.6. Select the rear vise jaw, (C) and the two rear top blocks, (L). Position therear top blocks on the frame rails so that the tab ears in the bottom ofthe blocks fit into the key holes of the frame rail. Position the top blocksso their raised posts are toward the rear of the frame, as shown inFigure 7. Now install the rear vise jaw so that the small holes in theends of the jaw fit over the raised posts on the top blocks you justinstalled.2 Year WarrantyGarantie de 2 ans2 Años de garantiaCopyright © 2000 Black & Decker Printed in CanadaCat. No. WM225 Type 3 Form 264519-03 Rev. 1 (Feb,00)INSTRUCTION MANUALWARNING: IMPORTANT SAFETY WARNINGSAND INSTRUCTIONSTO REDUCE RISK OF INJURY:• Before any use, be sure everyone using this tool reads and understandsall safety instructions and other information contained in this manual.• Save these instructions and review frequently prior to use and ininstructing others.READ ALL INSTRUCTIONS7. Insert the remaining two bolts, (M) into the holes in the jaw and throughthe top blocks into the raised posts of the vise guides. The holes in therear blocks are not threaded so you will feel resistance as you cutthreads into them.8. Snap-in crank handle as shown in Figure 8.9. To assemble the rubber feet to your Workmate: Turn the unit upsidedown. Swing out the four legs to the fully extended and locked position.Align the rubber foot with the leg as shown in Figure 9. Lightly tap footinto place with a hammer.CHANGING THE INDEXED POSITION OF THE REAR JAW:1. Install the rear jaw in 1 of 3 possible indexed “keyhole” positions byindexing the rear vise jaw into a keyhole in the vise jaw bracket. Securethe rear jaw by sliding it to the back of the keyhole. As shown in Figure 7.SWIVEL PEGS:1. The four supplied swivel pegs can be used in any of the holes in the frontand rear jaws. The pegs are used in any of the holes in the front andrear jaws. The pegs are used to extend the dimensions of yourWorkmate’s holding capacity. (Figure 10)Service InformationBlack & Decker offers a full network of company-owned and AuthorizedService locations throughout North America. All Black & Decker ServiceCenters are staffed with trained personnel to provide customers withefficient and reliable power tool service. Whether you need technical advice,repair, or genuine factory replacement parts, contact the Black & Deckerservice location nearest you. To find your local service location, refer to theyellow page directory under “Tools—Electric”or call: 1-800-54-HOW-TO.Full Two-Year Home Use WarrantyBlack & Decker (U.S.) Inc. warrants this product for two years against anydefects in material or workmanship. The defective product will be replacedor repaired at no charge in either of two ways:The first, which will result in exchanges only, is to return the product to theretailer from whom it was purchased (provided that the store is aparticipating retailer). Returns should be made within the time period of theretailer’s policy for exchanges (usually 30 to 90 days after the sale). Proof ofpurchase may be required. Please check with the retailer for their specificreturn policy regarding returns that are beyond the time set for exchanges.The second option is to take or send the product (prepaid) to aBlack & Decker owned or Authorized Service Center for repair orreplacement at our option. Proof of purchase may be required.Black & Decker owned and Authorized Service Centers are listed under“Tools-Electric” in the yellow pages of the phone directory. This warrantydoes not apply to accessories. This warranty gives you specific legal rightsand you may have other rights which vary from state to state. Should youhave any questions, contact the manager of your nearest Black & DeckerService Center.This product is not intended for commercial use.See ‘Tools-Electric’– Yellow Pages –for Service & SalesImported byBlack & Decker (U.S.) Inc.,701 E. Joppa Rd.Towson, MD 21286 U.S.A.A. FRAME B. FRONT JAW C. REAR JAWD. VISE SCREW E. PIVOT NUT F. VISE CRANKG. CRANK HANDLE H. SWIVEL PEGS J. SOCKET WRENCHK. FRONT TOP BLOCKS L. REAR TOP BLOCKS M. BOLTSN. PINS O. RUBBER FEETA. CADRE B. MÂCHOIRE AVANT C. MÂCHOIRE ARRIÈRED. VIS D’ÉTAU E. ÉCROU DE PIVOT F. MANIVELLE D’ÉTAUG. POIGNÉE DE MANIVELLE H. MORDACHES ORIENTABLES J. CLÉ À DOUILEK. CALES SUPÉRIEURES AVANT L. CALES SUPÉRIEURES ARRIÈRE M. BOULONSN. CHEVILLES O. BOUT DE CAOUTCHOUCA. BASTIDOR B. MORDAZA FRONTAL C. MORDAZA TRASERAD. ESPARRAGO E. TUERCA DE GIRO F. MANIVELA DE LAPRENSAG. ASA DE LA MANIVELA H. TOPES GIRATORIOS J. DADOK. BLOQUES DE REMATE L. BLOQUES DE REMATE M. TORNILLOSFRONTALES TRASEROSN. PERNOS O. REGATONES DE GOMAFIG. 3FIG. 4FIG. 8FIG. 6FIG. 9FIG. 5FIG. 1CDEFNGHOMLJKABFIG. 2FIG. 7RAISED POSTGOUJONPOSTETAB EARSOREILLES DE LAPROTUBÉRANCELENGÜETASFIG. 10 |
Related manuals for Black & Decker Workmate 225 Type 3
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved