![Black & Decker BRC300 Instruction Manual Manual pdf 1 page image](https://manuals-archive2.s3.amazonaws.com/4902409/a25dffeb9c395cd2508686c54414a4921f.jpg)
Black & Decker BRC300 Instruction Manual
Contents | ![]()
Assembly(STEP 1, FIG. A &B) Locate the black spray wand holder shown infigure A and attach it to the inside of the Brush and Roller Cleaner asshown in figure B.(STEP 2, FIG. C) Feed orange tube down through hole in top ofcleaner and into spray wand holder.(STEP 3) Attach the orange clip to the hose. Note: The clips acts as astorage area for the adaptor and hose when not in use.Catalog No. BRC300CAT. NO. BRC300 FORM NO. 640297-00 (APR- 06) COPYRIGHT © 2006 BLACK & DECKER PRINTED IN CHINAVEA EL ESPAÑOL EN LA CONTRAPORTADA.INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO YPÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTEINSTRUCTIVO ANTES DE USAR EL PRODUCTO.INSTRUCTION MANUALBBBB RRRR UUUU SSSS HHHH &&&& RRRR OOOO LLLL LLLL EEEE RRRR CCCC LLLL EEEE AAAA NNNN EEEE RRRRSAVE THIS MANUAL FOR FUTURE REFERENCE.Important Safety InstructionsWARNING! To reduce the risk of injury, user must read and understand instructionmanual.• Read all instructions before using the Brush and Roller Cleaner.• Always wear proper eye protection.• Always use proper drainage, test the drain with running water before attempting to use theBrush and Roller Cleaner.• Local disposal requirements vary; consult your sanitation department or state designatedenvironmental agency for disposal options.• Do not use hot water. It will not decrease the cleaning process and can damage the rollersleeve.• Do not use with oil based paints. Brush and Roller Cleaner can only be used with latexwater based paint.• Brush and Roller Cleaner should only be connected to a water supply with standardhousehold water pressure.SAVE THESE INSTRUCTIONSCleaning Brushes:(STEP 1, FIG. 1) Remove the aerator fromyour faucet and replace it with the faucetadaptor.(STEP 2, FIG. 2) Place the Brush and Roller Cleanerinto the sink and attach the hose to the faucet.(STEP 3, FIG. 3) Remove any excess paint from brushby scraping bristles on side of paint container. Insertbrush handle into brush holder.(STEP 4, FIG. 4) Remove the cap and insert brush intocanister, with paint brush icon pointing toward spraycontrol knob.Place top cap into position on the canister.(STEP 5, FIG. 5) Turn on faucet part way and check forleaks, then turn on faucet to full.(STEP 6, FIG. 6) Direct the spray to the center of thebrush, saturating the bristles with water.(STEP 7, FIG. 7) Direct the spray to the edge of thebrush, spinning brush to remove paint.• Repeat steps 6 & 7 until water runs clear.Cleaning Rollers(STEP 1,FIG. 8) Remove the aerator fromyour faucet and replace it with the faucetadaptor.BEFORE RETURNING THIS PRODUCTFOR ANY REASON PLEASE CALL1-800-544-6986BEFORE YOU CALL, HAVE THE CATALOG No. AND DATE CODE AVAILABLE. IN MOST CASES, ABLACK & DECKER REPRESENTATIVE CAN RESOLVE THE PROBLEM OVER THE PHONE. IF YOU HAVEA SUGGESTION OR COMMENT, GIVE US A CALL. YOUR FEEDBACK IS VITAL TO BLACK & DECKER.TT HANKHANK YOUYOU FORFOR CHOOSINGCHOOSING BB LACKLACK && DD ECKERECKER !!GG OO TT OO WWWWWW .B.B LACKANDLACKAND DD ECKERECKER .. COMCOM /N/N EWEW OO WNERWNERTT OO REGISTERREGISTER YOURYOUR NEWNEW PRODUCTPRODUCT ..1234567Operating Instructions8FEATURESA. CapB. Spray control knobC. Faucet adatorD. HoseE. Roller frame holderF. Brush holderG. Spray wand holderA BCCDEFGABC |
Related manuals for Black & Decker BRC300
This manual is suitable for:
Product
Menu
Learn More
Menu
Legal
Menu
Copyright © 2024 OneStart. All Rights Reserved