Black & Decker BDL190S-XE Instruction Manual

Contents

LASER RADIATION. AVOID DIRECT EYE EXPOSURE.RADIACIÓN LÁSER. EVITE LA EXPOSICIÓN DIRECTA DE LOS OJOS.MAXIMUM OUTPUT POWER< 5mW@633nm-670nm CLASS IIIa LASER PRODUCT. THIS PRODUCTCOMPLIES WITH THE APPLICABLE REQUIREMENTS OF 21CFR PARTS 1040.10 AND 1040.11.LÁSER CLASE IIIa CON MÁXIMA POTENCIA DE SALIDA < 5mW@633nm-670nm. ESTE PRODUCTOCUMPLE CON LOS REQUISITOS APLICABLES DE LAS PIEZAS 1040.10 Y 1040.11 DE 21CFR.DANGER PELIGROWARNING: Read and understand all instructions. Failure to follow all instructionslisted below may result in electric shock, fire and/or serious personal injury.SAVE THESE INSTRUCTIONSSafety Instructions• Do not operate the laser in explosive atmospheres, such as in the presence of flammableliquids, gases, or dust.• Use the laser only with the specifically designated batteries. Use of any other batteriesmay create a risk of fire.• Store idle laser out of reach of children and other untrained persons. Lasers are dangerousin the hands of untrained users.• Use only accessories that are recommended by the manufacturer for your model.Accessories that may be suitable for one laser, may create a risk of injury when used onanother laser.• Do not use optical tools such as a telescope or transit to view the laser beam. Serious eyeinjury could result.• Do not place the laser in a position which may cause anyone to intentionally orunintentionally stare into the laser beam. Serious eye injury could result• Turn the laser off when it is not in use. Leaving the laser on increases the risk of staringinto the laser beam.• Repairs and servicing MUST be performed by a qualified repair facility. Repairs performedby unqualified personnel could result in serious injury.• WARNING: DO NOT DISASSEMBLE THE LASER. There are no user serviceableparts inside. Disassembling the Laser will void all warranties on the product. Do not modifythe product in any way. Modifying the tool may result in Hazardous Laser RadiationExposure.• Do not operate the laser around children or allow children to operate the laser. Serious eyeinjury may result.• Do not remove or deface warning labels. Removing labels increases the risk of exposureto radiation.• Position the laser securely. Damage to the laser or serious injury could result if the laserfalls.• CAUTION: Occasionally, pipes and electrical wiring may not be detected by thisproduct. The sensor will not detect hot wires inside metal pipe or metal conduit, behindmetallic wall covering, or behind some plywood or other dense materials.• CAUTION: Material thickness, type of material, moisture content, and other variablescan affect sensing results. The sensor may detect electric wiring or pipes in the samemanner that studs are detected depending on their location to the wall surface. Usecaution when drilling, nailing or cutting into walls, floors and ceilings which may containelectrical wiring or pipes. These items may be detected by the sensor in the same mannerin which studs are detected. Because studs are normally spaced 16 inches (406 mm) or24 inches (610 mm) apart and are usually 1-1/2 inches (38 mm) wide, beware of anythingcloser together or of a different width. Always turn off the power when working nearelectrical wires.• CAUTION: Use of controls or adjustments or performance of procedures other thanthose specified in this manual may result in hazardous laser radiation exposure.• This product is intended for use in a temperature range of 50°F(10°C) - 104°F(40°C).Liquid Crystal Display (First Aid Measures)• If liquid crystal comes in contact with your skin:Wash area off completely with plenty of water. Remove contaminated clothing.• If liquid crystal gets into your eye:Flush the affected eye with clean water and then seek medical attention.• If liquid crystal is swallowed:Flush your mouth thoroughly with water. Drink large quantities of water and inducevomiting. Then seek medical attention.The label on your tool may include the following symbols.V ..........................volts mW......................milliwattsnm ........................wavelength in nanometers IIIa ......................Class IIIa Laser........................AC Wire WarningSAVE THIS MANUAL FOR FUTURE REFERENCE.INSTRUCTION MANUALAAAA uuuu tttt oooo LLLL eeee vvvv eeee llll iiii nnnn gggg LLLL aaaa ssss eeee rrrr ////WWWWoooo oooo dddd &&&& MMMM eeee tttt aaaa llll SSSS tttt uuuu dddd //// AAAA CCCC WWWW iiii rrrreeee SSSS eeee nnnn ssss oooo rrrrCat No. BDL190S-XE Form # 90588003March 2012 Copyright © 2012 Black & Decker Printed in ChinaLASER RADIATION. AVOID DIRECT EYE EXPOSURE.RADIACIÓN LÁSER. EVITE LA EXPOSICIÓN DIRECTA DE LOS OJOS.MAXIMUM OUTPUT POWER< 5mW@633nm-670nm CLASS IIIa LASER PRODUCT. THIS PRODUCTCOMPLIES WITH THE APPLICABLE REQUIREMENTS OF 21CFR PARTS 1040.10 AND 1040.11.LÁSER CLASE IIIa CON MÁXIMA POTENCIA DE SALIDA < 5mW@633nm-670nm. ESTE PRODUCTOCUMPLE CON LOS REQUISITOS APLICABLES DE LAS PIEZAS 1040.10 Y 1040.11 DE 21CFR.DANGER PELIGROLASER RADIATION. AVOID DIRECT EYE EXPOSURE.RADIACIÓN LÁSER. EVITE LA EXPOSICIÓN DIRECTA DE LOS OJOS.MAXIMUM OUTPUT POWER< 5mW@633nm-670nm CLASS IIIa LASER PRODUCT. THIS PRODUCTCOMPLIES WITH THE APPLICABLE REQUIREMENTS OF 21CFR PARTS 1040.10 AND 1040.11.LÁSER CLASE IIIa CON MÁXIMA POTENCIA DE SALIDA < 5mW@633nm-670nm. ESTE PRODUCTOCUMPLE CON LOS REQUISITOS APLICABLES DE LAS PIEZAS 1040.10 Y 1040.11 DE 21CFR.DANGER PELIGROLASER RADIATION. AVOID DIRECT EYE EXPOSURE.RADIACIÓN LÁSER. EVITE LA EXPOSICIÓN DIRECTA DE LOS OJOS.MAXIMUM OUTPUT POWER< 5mW@633nm-670nm CLASS IIIa LASER PRODUCT. THIS PRODUCTCOMPLIES WITH THE APPLICABLE REQUIREMENTS OF 21CFR PARTS 1040.10 AND 1040.11.LÁSER CLASE IIIa CON MÁXIMA POTENCIA DE SALIDA < 5mW@633nm-670nm. ESTE PRODUCTOCUMPLE CON LOS REQUISITOS APLICABLES DE LAS PIEZAS 1040.10 Y 1040.11 DE 21CFR.DANGER PELIGROLASER RADIATION. AVOID DIRECT EYE EXPOSURE.RADIACIÓN LÁSER. EVITE LA EXPOSICIÓN DIRECTA DE LOS OJOS.MAXIMUM OUTPUT POWER< 5mW@633nm-670nm CLASS IIIa LASER PRODUCT. THIS PRODUCTCOMPLIES WITH THE APPLICABLE REQUIREMENTS OF 21CFR PARTS 1040.10 AND 1040.11.LÁSER CLASE IIIa CON MÁXIMA POTENCIA DE SALIDA < 5mW@633nm-670nm. ESTE PRODUCTOCUMPLE CON LOS REQUISITOS APLICABLES DE LAS PIEZAS 1040.10 Y 1040.11 DE 21CFR.DANGER PELIGROFEATURESA.) Laser On/Off ButtonB.) Detector On/Off ButtonC.) AC Wire Indicator LEDD.) LCD ScreenE.) Wall Attachment -Hanging Cone (keyhole)F.) Wall Attachment -Drywall PinG.) Self-Leveling LaserLinesH.) Battery CompartmentCover (back side of unit)A2 3TaylorMadeTaylorMadeBonAirBonAirC.C.C.C.TaylorMadeBonAirBonAirC.C.C.C.TaylorMadeBonAirBonAirC.C.C.C.LASER RADIATION. AVOID DIRECT EYE EXPOSURE.RADIACIÓN LÁSER. EVITE LA EXPOSICIÓN DIRECTA DE LOS OJOS.MAXIMUM OUTPUT POWER< 5mW@633nm-670nm CLASS IIIa LASER PRODUCT. THIS PRODUCTCOMPLIES WITH THE APPLICABLE REQUIREMENTS OF 21CFR PARTS 1040.10 AND 1040.11.LÁSER CLASE IIIa CON MÁXIMA POTENCIA DE SALIDA < 5mW@633nm-670nm. ESTE PRODUCTOCUMPLE CON LOS REQUISITOS APLICABLES DE LAS PIEZAS 1040.10 Y 1040.11 DE 21CFR.DANGER PELIGROCatalog No.BDL190S-XEADBCF EGG54H167BipSonidoThank you for choosing Black & Decker!PLEASE READ BEFORE RETURNING THISPRODUCT FOR ANY REASON:If you can’t find the answer or do not have access to the internet,call 1-800-444-224 from 9 a.m. to 5 p.m. EST Mon. -- Fri. to speak with an agent.Please have the catalog number available when you call.www.blackanddecker.com.auMay 2012 90588096

/ 2

Related manuals for Black & Decker BDL190S-XE