Adcom GTP-870HD User Manual

Also see for GTP-870HD: Quick start guide Brochure

Contents

Adcom GTP-870HD User Manual Manual pdf 53 page image

53Chapter 3 - Setupwww.adcom.com GTP-870HD Owner’s ManualFunction Description Data ASCIIMain Volume UP 0x2B +Main Volume DOWN 0x2D -Main Mute 0x5B [Main Un-mute 0x5D ]Sleep OFF 0x1F USSleep (30) 0x20 SPACESleep (60) 0x21 !Sleep (90) 0x22 ”Sleep (120) 0x0A LFSleep (180) 0x12 DC2Test tone (noise) On 0x28 (Test tone (noise) Off 0x29 )VFD (Bright) 0x5C \VFD (Dim) 0x2C ,VFD (OFF) 0x23 #Dynamic Range Normal (100%) 0x25 %Dynamic Range 75% 0x40 @Dynamic Range 50% 0x3F ?Dynamic Range 25% 0x2F /Surround Mode select: (stepsthrough available modes)0x30 0Direct SurMode select: DOLBYDIGITAL0x38 8Direct SurMode select: DOLBY PROLOGIC0x31 1Direct SurMode select: DOLBY PLII-CINEMA0x53 SDirect SurMode select: DOLBY PLII-MUSIC0x2E .Direct SurMode select: DOLBY PLII-PANORAMA0x54 TDirect SurMode select: DOLBYDIGITAL EX0x32 2Direct SurMode select: DOLBY PLIIx-CINEMA0x0E SODirect SurMode select: DOLBY PLIIx-MUSIC0x0F SIFunction Description Data ASCIIDirect SurMode select: DOLBYPLIIx–PANORAMA0x10 DLEDirect SurMode select: DTS 0x34 4Direct SurMode select: DTS NEO:6-CINEMA0x51 QDirect SurMode select: DTS NEO:6-MUSIC0x52 RDirect SurMode select: DTS-ES 0x39 9Direct SurMode select: ADCOM7.1m2 STEREO0x33 3Direct SurMode select: 5 CHANNELSTEREO0x36 6Direct SurMode select: 2 CHANNELSTEREO0x37 7Direct SurMode select: HALL 0x35 5OSD Setup Menu (Toggle On/Off) 0x11 DC1OSD Navigation Up 0x5E ^OSD Navigation Down 0x5F _OSD Navigation Select / Enter 0x3D =OSD Navigation Left 0x3C <OSD Navigation Right 0x3E >Front Left Channel Trim + 0x55 UFront Left Channel Trim - 0x56 VFront Right Channel Trim + 0x57 WFront Right Channel Trim - 0x58 XSurround Left Channel Trim + 0x41 ASurround Left Channel Trim - 0x42 BSurround Right Channel Trim + 0x43 CSurround Right Channel Trim - 0x44 DSurround Back Left Channel Trim + 0x45 ESurround Back Left Channel Trim - 0x46 FSurround Back Right Channel Trim + 0x47 GSurround Back Right Channel Trim - 0x48 HCenter Channel Trim + 0x49 ICenter Channel Trim - 0x4A JSubwoofer Channel Trim + 0x4B KDiscrete Remote Control CommandsThe GTP-870HD can be controlled via its serial RS-232 port. The serial port can be connected to a media con-trol center, PC, or ‘dumb terminal’ via a straight-through standard 9-pin serial port cable (MALE on one endand FEMALE on the other end). When using a PC, a terminal emulator program (e.g. HyperTerminal), can beused to control the GTP-870HD. The communications parameters should be set as follows:• 9600 baud, 8 data bits, no parity, 1 stop bit, and Flow Control: Hardware.• All serial port control commands are structured as a four byte packet or string “, , ,”.• SPECIAL RESERVED CHARACTERS: Start Of Packet = 0x7B = “{“ (The Left Curly Bracket); EndOf Packet = 0x7D = “}” (The Right Curly Bracket).• Example syntax for the Discrete Remote Control Command for ‘Main Volume UP’ expressed as a hexadecimalstring: 0x7B, 0x44, 0x2B, 0x7D