Ablerex GR1200 User Manual

Also see for GR 2000: User manual

Ablerex GR1200 User Manual Manual pdf 1 page image

1USER’S MANUALGR1200This manual contains important safety instructions. Please follow all instructions during installation. Read this manual thoroughly before unpacking,installing or operating.Caution: Risk of Electric Shock• The UPS contains batteries. The output outlets may be electrically live even when the UPS is disconnected from the AC mains.• The UPS contains potentially hazardous voltages. Do not open the units as there are no user serviceable parts. All maintenance andservicing should be performed by qualified service personnel.• Risk of electric shock, Battery Circuit is not isolated from AC input, hazardous voltage may exist between battery terminals and ground. Testbefore servicing and use insulated tools.NOTE: The UPS is designed to be for use with computer loads only.Caution：Do not connect a laser printer to the UPS.A laser printer draws significantly more power than other types of equipment and may overload the UPS.SETUP1 InspectionInspect the UPS upon receipt.Notify the carrier and dealer if thereis damage. The package isrecyclable; save it for reuse ordispose of it properly.Inspect accessories:① Power cable 1PCSUSER MANUAL 1PCS2 Choose an installation location- Avoid locations that are excessively humid, near water,near heat sources or in direct sunlight- Allow 1inch (2.5cm) clearance on each side of the UPS3 Connecting Equipment and Power to the UPS4 Connect Modem/ Phone / Network for Surge Protection (Optional) 5 Connect Interface Device 6 Turn ON/OFF the UPSTurn on the UPS: Press the UPSOn/OFF Switchfor approx. 3seconds, then the Buzzer soundstwice, the UPS will start-up.Turn off the UPS: Press the UPSOn/OFF Switch for approx. 3seconds, then the Buzzer soundstwice, the UPS will shutdown.7 Cold Start FunctionWhen the UPS is OFF and no utility inputpower is present, use the “Cold Start”feature to apply power to the loads fromUPS‘s battery. Press the “ON/OFF” switchuntil the UPS beeps.8 Software Download and InstallationPlease follow steps below to download and install monitoring software:1. Go to the website http://www.ablerex.com.sg/downloads.html2. Depending on the computer OS, select Emily software (for Win 7&8 OS, select Emily2) and click download.3. Follow the on-screen instructions to install the software.4. When the computer restarts, the monitoring software automatically search and connects to the UPS.FRONT PANEL EXPLANATIONSGR600/GR800–LEDFRONTPANEL(STANDARD) Symbol LEDColor Description/function GR600/GR800/R1200/GR1800/GR2000– LCD FRONT PANEL(OPTION)N/A Turn-on/Turn-off SwitchGreenLit: Line modeDim: Abnormal inputvoltage and frequency 1.Line mode 4. Battery capacity 7.FaultYellow Lit: Battery modeFlashing: Battery Low2.Battery mode 5. Load level 8.Tack switch forTurn-on/Turn-off3.AVR mode 6.MeasurementTarget & ValueRed Lit: System malfunctionor abnormalGR1200/GR1800/GR2000 – LEDFRONT PANEL(STANDARD)Symbol LEDColorDescription/function REAR PANEL EXPLANATIONSN/A Turn-on/Turn-off Switch GR600/GR800 REAR PANEL1. AC Input Outlet2. Fuse3. Output Connector:4x Thailand Outlets4. USB (Standard)GR1200/GR1800/GR2000 REAR PANEL1. AC Input Outlet2. Fuse3. Output Connector:6x Thailand Outlets4. USB (Standard)5. FanGreen Lit: Line modeFlashing: Battery modeRed Lit: System malfunction orabnormalN/A LoadN/A BatteryGreen Load Percentage/Battery CapacityStep1: Connect the UPS to theAC mains.Step2: Connect the equipmentto the UPS output outlets.Step3: Switch on the AC Mains,follow by the UPS then theequipment last.*Plug the UPS into the ACMains to charge for 8 hoursbefore using the UPS.- For modem/phone line protection,connect equipment to the RJ11port using RJ11 cable.- For surge protection, connectequipment to the RJ45 port usingEthernet/RJ45 cable.The UPS is equipped withtwo interface ports: a USBport (Standard) and a 9-pinRS232 port (Optional)allowing advancedcommunication networkbetween the UPS and acomputer (network).12 3541234

/ 2

Related manuals for Ablerex GR 2000