OneStart

Menu

ABB HTP500 User Manual

Page 1 preview
Page 2 preview
Page 3 preview
Page 4 preview
Page 5 preview
Page 6 preview
Page 7 preview
Page 8 preview
Page 9 preview
Page 10 preview
Page 11 preview
Page 12 preview
Page 13 preview
Page 14 preview
Page 15 preview
Page 16 preview
Page 17 preview
Page 18 preview
Page 19 preview
Page 20 preview
Page 21 preview
Page 22 preview
Page 23 preview
Page 24 preview
Page 25 preview
Page 26 preview
Page 27 preview
Page 28 preview
Page 29 preview
Page 30 preview
Page 31 preview
Page 32 preview
Page 33 preview
Page 34 preview
Page 35 preview
Page 36 preview
Page 37 preview
Page 38 preview
Page 39 preview
Page 40 preview
Page 41 preview
Page 42 preview
Page 43 preview
Page 44 preview
Page 45 preview
Page 46 preview
Page 47 preview
Page 48 preview
Page 49 preview
Page 50 preview
Page 51 preview
Page 52 preview
Page 53 preview
Page 54 preview
Page 55 preview
Page 56 preview
Page 57 preview
Page 58 preview
Page 59 preview
Page 60 preview
Page 61 preview
Page 62 preview
Page 63 preview
Page 64 preview
Page 65 preview
Page 66 preview
Contents
  1. C ONTENTS
  2. INTRODUCTION
  3. A CCESSORIES
  4. PREPARING OF THE HTP500 V2 ON PRINTING
  5. please wait
  6. POWER SUPPLY CABLE CONNECTION
  7. LOADING / REMOVING THE CLEANING CASSETTE
  8. LOADING A RIBBON CASSETTE
  9. REMOVING A PLATE
  10. DRIVER AND SOFTWARE INSTALLATION
  11. C ENTERING
  12. C ALIBRATION
  13. P RINTER D RIVER U NINSTALL
  14. F EEDER ACCESSORIES
  15. P RINT ON CABLE TAGS
  17. P REPARING THE PRINTER
  18. P RINTER
  19. P RINT ON TAGS AND STRIPS
  20. TROUBLE SHOOTING
  21. PRINTER MESSAGES / ERRORS
  22. DAILY CARE
  23. CLEANING AND STORING PLATES
  24. TEST PRINT
  25. PACKAGING AND TRANSPORTATION
  26. P ACKAGING
ABB HTP500 User Manual Manual pdf 57 page image
JAMMED PLATEUtilize only the “MENU – REMOVE” function to eject the item from the printer.Press “ONLINE” and then “MENU”With the right arrow select “REMOVE” and press the right or left arrow to eject the itemREMOVING THE PLATE WITH STRENGHT OR NOT USING THE ‘REMOVE’ FUNCTIONMIGHT DAMAGE WITH NO SOLUTION THE HEAD PRINT.CANCEL for 3 seconds - ABORT A PRINTTo abort a print and cancel print data, press Cancel at least for three seconds straight beforethe printer has started to print.7.2 TROUBLE SHOOTINGPrinter won’t turn on Is the power cord properly plugged into a power outlet?Connect the printer power cord to the printer power connector, then plug it into an AC outlet. Is the power switch turned on?Turn on the printer.Printer won’t go Online Is the cassette cover well closed?Make sure that the cassette cover is completely closed, then press ONLINE. Is the ribbon cassette properly loaded?Ensure that there are no slacks in the ribbon before loading the ribbon cassette properly onits mount.PC won’t communicate with the printer Is the USB interface cable properly connected?Ensure that the USB interface cable is properly connected with the printer and the PC. Is the printer driver installed on your PC?Before printing, install the printer driver on your PC.Plate is not normally transported Is the item jammed inside the printer?If a plate jams inside the printer, use the REMOVE function following the procedure below.Select REMOVE from the Menu1)Press the ONLINE button to put the printer OFFLINE. The ONLINE led turns off.2)Press the button [Menu/ ] to enter in the Menu.3)Press the button [Menu/ ] and [ ] to select REMOVE, press ENTER to confirm4)Keep pressed the button [Menu/ ] or [ ] to rotate the conveyor roller, ejecting the item outof the printer.REMINDIf the plate is too short to be load, press Enter to eject the plate from the printer.Using the Enter button to remove a jammed plate, could damage the print head. Thismethod should be used only when the plate is too short and pressing [Menu/ ] and [ ]
/ 66
This manual is suitable for:
HTP500HTP500 V2
Product
Menu
Learn More
Menu
Legal
Menu
Copyright © 2024 OneStart. All Rights Reserved