OneStart

Menu

Fujitsu Primergy BX920 S4 manuals

Primergy BX920 S4 first page preview

Primergy BX920 S4

Brand: Fujitsu | Category: Server
Table of contents
  1. server blade
  2. copyright and trademarks
  3. Table Of Contents
  4. Table Of Contents
  5. Table Of Contents
  6. Table Of Contents
  7. Table Of Contents
  8. Table Of Contents
  9. Table Of Contents
  10. Table Of Contents
  11. Table Of Contents
  12. version history
  13. Introduction
  14. Notational conventions
  15. Before you start
  16. Classification of procedures
  17. Upgrade and Repair Units (URU)
  18. Field Replaceable Units (FRU)
  19. Average task duration
  20. Tools you need at hand
  21. Documents you need at hand
  22. Important information
  23. CE conformity
  24. FCC Class A Compliance Statement
  25. Environmental protection
  26. Basic hardware procedures
  27. Locating the defective server blade
  28. Determining the error class
  29. Global Error indicator
  30. Customer Self Service (CSS) indicator
  31. Locating the defective component
  32. component leds
  33. Opening the rack door
  34. Shutting down the server blade
  35. Removing a server blade
  36. Removing the server blade from the system unit
  37. Opening the server blade
  38. Closing the server blade
  39. Installing the server blade in the system unit
  40. Switching on the server blade
  41. Concluding software tasks
  42. Closing the rack door
  43. Basic software procedures
  44. Checking the server blade status via iRMC
  45. Saving BIOS settings
  46. Disabling BitLocker functionality
  47. Disabling boot watchdog functionality
  48. Verifying and configuring the backup software solution
  49. Note on server maintenance in a Multipath I/O environment
  51. Switching on the ID indicator
  52. Completing the maintenance task
  53. Updating or recovering the iRMC
  54. Restoring BIOS settings
  55. Enabling Option ROM scan
  57. Resetting the boot retry counter
  58. Enabling boot watchdog functionality
  59. Enabling replaced components in the system BIOS
  60. Verifying the system time settings
  61. Viewing and clearing the System Event Log (SEL)
  62. Saving the SEL
  63. Clearing the SEL
  64. Enabling BitLocker functionality
  65. Performing a RAID array rebuild
  66. Looking up WWN addresses
  67. Using the Chassis ID Prom Tool
  68. After replacing the server blade
  69. Hard disk drives / solid state drives
  70. Basic information
  71. General equipping rules
  72. Installing a 2.5-inch HDD/SSD module
  73. Installing the 2.5-inch HDD/SSD module
  74. Concluding steps
  75. Removing a 2.5-inch HDD/SSD module
  76. Removing the 2.5-inch HDD/SSD module
  77. Installing the 2.5-inch dummy module
  78. Replacing a 2.5-inch HDD/SSD module
  79. Preliminary steps
  80. Replacing HDD/SSD backplanes
  81. Removing the HDD/SSD backplane
  82. Installing the HDD/SSD backplane
  84. Expansion cards and backup units
  85. Mezzanine cards
  86. Installing riser cards
  87. Removing riser cards
  88. Population rules for mezzanine cards
  89. expansion cards and backup units
  90. Installing mezzanine cards
  91. Installing a mezzanine card
  93. Removing mezzanine cards
  94. Removing a mezzanine card
  96. Replacing mezzanine cards
  98. SAS RAID HDD module
  99. Installing the SAS RAID HDD module
  102. Removing the SAS RAID HDD module
  104. Replacing the SAS RAID HDD module
  106. Installing the FBU (Flash Backup Unit)
  107. Installing the FBU
  109. Removing the FBU (Flash Backup Unit)
  110. Removing the FBU
  112. Replacing the FBU (Flash Backup Unit)
  116. Main memory
  117. Memory sequence
  118. Independant Channel mode
  119. Mirrored channel mode
  120. Performance channel mode
  121. Rank Sparing Mode for quad rank (4R) and octa rank (8R LRDIMM modules (minimizing waste of spare memory)
  122. Dummy DIMM modules
  123. Installing memory modules
  124. Installing a memory module
  126. Removing memory modules
  127. Removing a memory module
  129. Replacing memory modules
  132. Handling of memory air cowls
  133. Removing the air cowls
  134. Processors
  135. Installing processors
  137. Installing a processor
  139. Removing processors
  140. Removing a processor
  142. Upgrading or replacing processors
  143. Upgrading or replacing a processor
  144. Handling processor heat sinks
  145. Installing processor heat sinks
  146. Preparing the heat sink and processor
  147. Installing the heat sink
  148. Removing processor heat sinks
  149. Replacing processor heat sinks
  150. Applying thermal paste
  151. System board components
  152. Required tools
  153. Removing the battery
  154. Installing the CMOS battery
  156. USB Flash Module (UFM)
  157. Installing the UFM
  158. Software configuration
  159. Removing the UFM
  161. Replacing the UFM
  162. Re-installing the UFM
  164. Trusted Platform Module (TPM)
  165. Installing the TPM
  167. Removing the TPM
  171. Replacing the TPM
  172. Re-installing the TPM
  174. Onboard SAS enabling key
  175. Removing the defective onboard SAS enabling key
  176. Installing the new onboard SAS enabling key
  178. Replacing the system board
  181. Removing the system board
  182. Installing the system board
  183. Swapping the processor
  185. Server blade
  186. Replacing the server blade
  187. Appendix
  188. Server blade interior
  189. Configuration tables
  190. Connectors and indicators
  191. Onboard settings
  192. Onboard indicators and controls
  193. Connectors and indicators on the front
  194. Front panel indicators
  195. Indicators on the hot-plug HDD/SSD module
  196. Minimum startup configuration
Primergy BX920 S4 first page preview

Primergy BX920 S4

Brand: Fujitsu | Category: Server blade
Related products
PRIMERGY BX920 S1PRIMERGY BX924 S4PRIMERGY BX920 S2Primergy BX920 S3PRIMERGY BX620 S4PRIMERGY BX924 S3PRIMERGY BX924 S2PRIMERGY BX922 S2PRIMERGY BX900Primergy BX900 S2
Fujitsu categories
Air Conditioner
Storage
Laptop
Server
Monitor
Printer
Scanner
Desktop
Motherboard
Microcontrollers
More Fujitsu categories
Product
Menu
Learn More
Menu
Legal
Menu
Copyright © 2024 OneStart. All Rights Reserved