Magnetek IMPULSE 4045-VG+S4 manuals

IMPULSE 4045-VG+S4

Brand: Magnetek | Category: Controller

Table of contents

1. Table Of Contents
2. Table Of Contents
3. Table Of Contents
4. Table Of Contents
5. How to Use This Manual
6. Introduction
7. IMPULSE®•G+ & VG+ Series 4 General Specifications
8. AC Reactor Specifications
9. S4IF Interface Specifications
10. IMPULSE®•G+ & VG+ Series 4 System Components And External Devices
11. Long Time Storage
12. Installing the Drive
13. Multiple Drive Installation (Side-by-Side Installation)
14. Drive Derating Data
15. IMPULSE®•G+ & VG+ Series 4 Wiring Practices
16. Suggested Circuit Protection Specifications and Wire Size
17. Power Circuit Wiring Procedures
18. Main Circuit Connection Diagram
19. Terminal Block Configuration
20. Insulation Barrier
21. Interface Circuit Board
22. Dip Switches
23. Sinking/Sourcing Mode Selection for Safe Disable Inputs
24. Control Circuit Terminals
25. S4IF Control Circuit Terminal Diagrams
26. Safe Torque Off
27. Wiring the Encoder Circuit
28. Encoder Wiring Diagrams and Information
29. Overview
30. Using the Keypad
31. Keypad LED and Button Functions
32. Parameter Modes
33. Initialization Set-up
34. X-Press Programming™
35. Initialize Parameters (A01-05)
36. User Parameters (A02-01 through 32)
37. Auto-Tuning
38. Standard Auto-Tune (T01-01 = 0) Instructions
39. Non-Rotational Auto-Tune (T01-01 = 1) Instructions
40. Terminal Resistance Auto-Tune (T01-01 = 2) Instructions
42. Reference Limits
43. Sequence/Reference Source
44. Stop Method
45. Coast to Stop (B03-03=1)
46. Motor Rotation Change
47. Acceleration/Deceleration
48. Accel/Decel Time Switching Frequency
49. Special Functions
50. Quick Stop™
51. Reverse Plug Simulation™
52. Micro-Speed™
53. End of Travel Limits
54. Phantom Stop
55. Klixon
56. Hook Height Measurement
57. Electronic Programmable Limit Switches (EPLS)
58. Lower Limit/Upper Limit Bypass MFDI
59. Load Float
60. OLV and FLV Operation (A01-02 = 02 and 03)
61. Swift-Lift™ & Ultra-Lift™
62. Configuring the Swift-Lift & Ultra-Lift Function
63. Torque Limit
64. Anti-Shock
65. No-Load Brake Hoist (VG+)
66. E-Lift (VG+)
67. Digital Input Option Set-up (DI-A3 and S4IO)
68. Weight Measurement
69. System Tare and Calibration for Weight Measurement
70. Slack Cable Detection
71. Snap Shaft Detection
72. Brake Delay Timers
73. Maintenance Timer
74. Inching Control
75. Index Function
76. Tuning
77. Motor Slip Compensation
78. Automatic Speed Regulator (ASR) Tuning
79. Torque Control
80. Speed/Torque Control Switching
81. S-Curve Acceleration/Deceleration
82. Carrier Frequency
83. Hunting Prevention
84. Motor Parameters
85. Motor Set-up
86. Test Mode Configuration
87. Option Card Parameters
88. Analog Input (AI-A3) Option Set-up
89. Analog Output (AO-A3) Option Set-up
90. Digital Output (DO-A3) and S4IO Option Set-up
91. Profibus-DP Communication Option Card Set-up
92. Ethernet Option Card Set-up (Ethernet IP & Modbus TCP/IP)
93. Terminal Parameters
94. F1 and F2 Keys Function Selection
95. Digital Outputs
96. Digital Outputs—Alarm/Fault Annunciate (H02-01–03=40)
97. Analog Inputs
98. Analog Outputs
99. Serial Communication Set-up
100. Pulse Train Input/Output
101. Protection Parameters
102. Power Loss Ride Thru
103. Stall Prevention
104. Speed Agree
105. Test Mode
106. Torque Detection
107. Hardware Protection
108. Automatic Fault Reset
109. Fault Latch Selection
110. Operator Parameters
111. Keypad Key Selection
112. Maintenance History
113. Copy Function
114. Monitor Parameters
115. Troubleshooting the Drive
116. Troubleshooting Encoder Related Faults
117. Fault Code: PGO-X-S/PGO-X-H–Pulse Generator Signal Fault
118. Fault Code: BE1–Rollback Fault
119. Fault Code: BE3–Brake Release Fault
120. Alarm Code: BE6–Brake Proving Alarm
121. Fault Code: OC–Over Current Fault
122. Fault Display and Corrective Actions at Auto-Tuning
123. Troubleshooting Option Card Related Faults
124. Copy Function Related Faults
125. Power Section Check
126. S4IF Replacement Procedure