GE EPSCPE100 manuals

EPSCPE100

Brand: GE | Category: Controller

Table of contents

1. Table Of Contents
2. Table Of Contents
3. Table Of Contents
4. Table Of Contents
5. Table Of Contents
6. Table Of Contents
7. Table Of Contents
8. Chapter 1 Introduction
9. Revisions in this Manual
10. PROFINET Controller Description
11. Embedded PROFINET Controller
12. PNC001 Module Specifications
13. Operating Range for Surrounding Air Temperature
14. PNC001 Module Controls and Indicators
15. PNC001 Hardware Implementions (-Ax & -Bxxx)
16. Ethernet Network Ports
17. USB Port(s)
18. PROFINET Networks for PACSystems
19. Compression
20. Basic System: One RX3i CPU and One PROFINET Controller using a single port
21. Basic System: One RX3i CPU and One PROFINET Controller using multiple ports
22. Basic System: Third-Party Devices and PME Programmer
23. Systems with One RX3i CPU and Two PROFINET Controllers
24. Figure 10: RX3i System with two PNC001 modules and two Daisy-Chain PROFINET LANs
25. One RX3i CPU with Four Controllers on Separate Networks
26. Two RX3i CPUs with Two PROFINET Networks and One Ethernet Network
27. Systems that use PROFINET System Redundancy (PNSR)
28. Systems that use Hot Standby CPU Redundancy
29. RSTi-EP Standalone CPU with embedded PROFINET Controller using a single port
30. RSTi-EP Standalone CPU with embedded PROFINET Controller using multiple ports
31. RSTi-EP Standalone CPU with embedded PROFINET Controller using MRP
32. Glossary
33. Documentation
34. Chapter 2 Installation
35. Pre-Installation Check
36. Installation in Hazardous Areas
37. Removing the Backplane Knockout
38. Module Installation
39. Hot Insertion and Removal
40. Ethernet Port Connections
41. Figure 22: Interconnect using Copper Cables / RJ45 Connectors
42. Figure 25: CAT5e/CAT6 (shielded or unshielded) with RJ 45 Connector
43. Installing SFP Devices
44. Removing SFP Devices
45. PNC001 LED Behavior
46. Detailed LED Descriptions
47. Installing the USB Port Driver
48. Firmware Updates
49. PNC001 Time Synchronization with the Host RX3i CPU
50. Chapter 3 Configuration
51. Configuration Overview
52. Basic Configuration Steps
53. Configuration Tools
54. Configuring an RX3i PROFINET Controller
55. Configuring an Embedded RSTi-EP PROFINET Controller
56. Configuring PROFINET System Redundancy
57. Exploring PROFINET Networks
58. Configuring a PROFINET Controller on a LAN
59. Configuring PROFINET Controller Parameters
60. Figure 42: Setting the Status Reference Address
61. Figure 44: Setting Media Redundancy Parameters
62. Configuring PROFINET LANs
63. Configuring the LAN Properties
64. Adding a VersaMax PROFINET Scanner to a LAN
65. Configuring VersaMax PROFINET Scanner Parameters
66. Figure 56: PNS Parameters Redundancy Tab
67. Figure 59: PNS Parameters Module Parameters Tab
68. Figure 61: PNS Interface Parameter Details
69. Adding VersaMax PROFINET Scanner Power Supplies
70. Adding VersaMax Modules to a Remote Node
71. Installing Power Supplies Between Modules
72. Configuring VersaMax Module Parameters
73. Figure 70: Selecting the Sub-Module Configuration with Jumper Settings Declared
74. Adding a Third-Party IO-Device to a LAN
75. Editing Third-Party IO-Device Parameters
76. Figure 77: Third-Party I/O: Configure Ring Ports for Media Redundancy Manager
77. Configuring Sub-Modules of a Third-Party IO-Device
78. Viewing / Editing IO-Device Properties
79. Figure 84: Assigning Reference Variable to IO-Device
80. Assigning IO-Device Names
81. Figure 88: List of Device Names on LAN with Status Indications
82. After the Configuration is Stored to the RX3i CPU
83. Chapter 4 PROFINET System Operation
84. PROFINET Operation Overview
85. PROFINET Communications
86. Figure 90: Real-Time and Non-Real-Time Data Communications
87. Operations of the PROFINET Controller in the PACSystems System
88. Duplicate PROFINET IO-Controller IP Address
89. I/O Scanning
90. Data Coherency
91. Performance Factors
92. PROFINET IO Update Rate Configuration
93. PACSystems CPU Operations for PROFINET
94. PNIO_DEV_COMM Function Block
95. Reset Smart Module for the PROFINET Controller
96. Scan Set I/O for Remote I/O Modules
97. Chapter 5 Diagnostics
98. Power-up and Reset (PNC001 Module)
99. Problems During Power-up and Reset
100. Special LED Blink Patterns
101. Status Reporting
102. I/O Fault Contacts
103. Fault Locating References
104. Fatal Error Reporting
105. PROFINET IO Alarms
106. Local Log Table of the PROFINET Controller
107. Faults Unique to Local Log Table
108. Viewing and Clearing the Local Log Table
109. Figure 96: Log Details Display
110. Figure 97: Log Details of a Specific Log Entry
111. PROFINET Controller Faults in the PACSystems Fault Tables
112. Faults Reported to the PACSystems I/O Fault Table
113. Chapter 6 Redundant Media
114. PROFINET Media Redundancy Protocol
115. MRP Failover Performance
116. Bumpless Operation with MRP
117. MRP Operation for I/O Update Rates of 16ms or Greater
118. Minimum I/O Update Rates for Bumpless Operation in an MRP Ring Topology
119. MRP Ring Ethernet Traffic Storm Prevention
120. Third-party MRP Manager Use with PROFINET Controller as MRP Client
121. Ring Topology with One Controller
122. Ring Topology with Multiple Controllers
123. Setting Up Media Redundancy Protocol
124. Sequence for Enabling Media Redundancy
125. Sequence for Replacing a Media Redundancy Manager
126. Procedure for Disabling Media Redundancy
127. Chapter 7 Network Management
128. SNMP
129. Supported SNMP Features
130. MIB-II Groups Supported
131. MIB-II System Group Values
132. LLDP
133. LLDP TLVs
134. Appendix A PROFINET IO Performance Examples
135. A-1 Systems with RX3i PNS
136. A-2 Systems with VersaMax PNS
137. A-2.2 VersaMax System Descriptions
138. A-3 Systems with RSTi-EP EPSCPE100/CPE115
139. A-3.2 RSTi-EP System Descriptions