ABB ACS800-37-0320-7 manuals

ACS800-37-0320-7

Brand: ABB | Category: Controller

Table of contents

1. What this chapter contains
2. Installation and maintenance work
3. Grounding
4. Operation
5. Permanent magnet motor drives
6. Table Of Contents
7. Table Of Contents
8. Table Of Contents
9. Table Of Contents
10. Table Of Contents
11. Table Of Contents
12. Table Of Contents
13. Table of contents
15. Installation and commissioning flowchart
16. Inquiries
17. Terms and abbreviations
19. Frame R6
20. Frame R7i
21. Frame R8i
22. Swing-out frame
23. Cabling direction
24. Single-line circuit diagram of the drive
25. Operation principle
26. AC voltage and current waveforms
27. Motor-side converter
28. Controls
29. Door switches
30. The ACS800
31. Fieldbus control of the line-side converter
32. Type code
33. Frame sizes 2×R8i to 6×R8i
35. Moving the unit
36. by fork-lift or pallet truck
37. Final placement of the unit
38. Before installation
39. Installation procedure
40. Fastening the cabinet to the floor (Non-marine units)
41. Holes inside the cabinet
42. Fastening the unit to the floor and wall (Marine units)
43. Joining the shipping splits
44. Connecting the DC busbars and the PE busbar
45. DC busbars
46. Miscellaneous
47. Cooling air intake through bottom of cabinet
48. Electric welding
50. Protecting the motor insulation and bearings
51. Requirements table
52. Permanent magnet synchronous motor
53. Supply (AC line) cable short-circuit protection
54. Prevention of unexpected start
55. Selecting the power cables
56. Alternative power cable types
57. Additional US requirements
58. Power factor compensation capacitors
59. Before opening an output contactor (in DTC motor control mode)
60. Selecting the control cables
61. Connection of a motor temperature sensor to the drive I/O
62. Control cable ducts
65. Input power connection – Frame R6
66. Input power connection – Frame R7i
67. Input power connection – Frame size R8i
68. Input power connection – Frame size 2×R8i and up
69. Motor connection – Frame R6
70. Motor connection – Frame R7i
71. Motor connection – Frame R8i units without option +E202 or +H359
72. Motor connection – Frame R8i with option +E202 but without +H359
73. Motor connection – Units with common motor terminal cubicle (+H359)
74. Motor connection – Frame 2×R8i and up without common motor terminal cubicle
75. Connection procedure
76. Control connections
77. Installation of optional modules and PC
78. Tap settings of the auxiliary voltage transformer (Frame R8i and up)
80. External control connections (non-US)
81. External control connections (US)
82. RMIO board specifications
83. Relay outputs
85. Start-up procedure
86. Starting the supply unit
87. ACS800-37-specific parameters in the IGBT Supply Control Program
88. Fixed parameters with the ACS800-37
89. ACS800-37-specific parameters in the application program
90. Actual signals and parameters of line-side converter in motor-side converter program
92. Reduced run capability
93. Quick connectors (Frame R8i and up)
94. Cooling fans
95. Supply/Inverter module cooling fan replacement (Frame R7i)
96. LCL filter module cooling fan replacement (Frame R7i)
97. Supply and inverter module cooling fan replacement (Frame R8i and up)
98. LCL filter cooling fan replacement (Frame R8i and up)
99. Cabinet fan replacement (Frame R6)
100. Cabinet fan replacement (Frame R8i and up with IP54)
101. Heatsinks
102. Other maintenance actions
103. Faults and warnings displayed by the CDP-312R Control Panel
104. LEDs of the drive
106. Symbols
107. Derating
108. NEMA ratings
110. ACS800-37 frame sizes and power module types
111. AC fuses
112. DC fuses
113. Input power connection
114. Motor connection
115. Efficiency
116. Materials
117. CE marking
118. Second environment (drive of category C3)
119. C-tick" marking
121. Equipment warranty and liability
125. Frame R8i (without option +E202)
126. Frame size R8i (with option +E202)
127. Frame size 2×R8i
128. Frame size 3×R8i
129. Frame size 4×R8i
130. Frame size 5×R8i
131. Frame size 6×R8i
133. Chopper/Resistor combinations – Technical data
134. Brake choppers – Technical data
135. Verifying the capacity of the braking equipment
136. Calculating the maximum braking power (P br )
137. Example 3
138. Custom resistor installation and wiring
139. Brake circuit commissioning