red lion IFMA0035 Manual

Contents

red lion IFMA0035 Manual Manual pdf 1 page image

SIMPLE ON-LINE RANGE SETTING(Using Actual Input Signal or Signal Generator)USER SETTABLE FULL SCALE FREQUENCY FROM1 Hz to 25 KHzFOUR OUTPUT OPERATING RANGES(0 to 5 V, 0 to 10 V, 0 to 20 mA, and 4 to 20 mA)PROGRAMMABLE INPUT CIRCUIT ACCEPTS OUTPUTS FROM AVARIETY OF SENSORS85 to 250 VAC and 9 to 32 VDC POWERED VERSIONSAVAILABLELOW FREQUENCY CUT-OUT AND OVERRANGE INDICATION3-WAY ELECTRICAL ISOLATION (POWER/INPUT/OUTPUT)INPUT AND OUTPUT INDICATION LEDsMODEL IFMA - DIN-RAIL FREQUENCY TO ANALOG CONVERTERDESCRIPTIONThe Model IFMA accepts a frequency input, and outputs an analog voltage orcurrent in proportion to the input frequency, with 0.1% accuracy. The full scaleinput frequency can be set to any value from 1 Hz to 25 KHz, either with afrequency source, or digitally with the on-board rotary switch and push-button.The IFMA utilizes a seven position DIP switch, a rotary switch, a push-buttonand two indication LEDs to accomplish input circuit configuration, operationalparameter set-up, and Input/Output indication. The input circuitry is DIP switchselectable for a variety of sources.The indication LEDs are used during normal operation to display the inputand output status of the IFMA. These LEDs are also used to provide visualfeedback to the user of the existing parameter settings during parameter set-up.The IFMA operates in one of four output modes. The programmable minimumand maximum response times provide optimal response at any input frequency.The unit is equipped with a universal mounting foot for attachment tostandard DIN style mounting rails, including top hat profile rail according to EN50 022 - 35 x7.5 and 35 x 15, and G profile rail according to EN 50 035 - G 32.SAFETY SUMMARYAll safety related regulations, local codes and instructions that appear in themanual or on equipment must be observed to ensure personal safety and toprevent damage to either the instrument or equipment connected to it. Ifequipment is used in a manner not specified by the manufacturer, the protectionprovided by the equipment may be impaired.SPECIFICATIONS1. POWER:AC Operation: 85 to 250 VAC, 48 to 62 Hz; 6.5 VADC Operation: 9 to 32 VDC; 2.5 WPower Up Current: Ip = 600 mA for 50 msec. max.2. SENSOR POWER: (AC version only) +12 VDC ±25% @ 60 mA max.3. OPERATING FREQUENCY RANGE:From 0 Hz to 25 KHz; user selectable.4. SIGNAL INPUT: DIP switch selectable to accept signals from a variety ofsources, including switch contacts, outputs from CMOS or TTL circuits,magnetic pickups, and all standard RLC sensors.Current Sourcing: Internal 1 K pull-down resistor for sensors with currentsourcing output. (Max. sensor output current = 24 mA @ 24 V output.)Current Sinking: Internal 3.9 K pull-up resistor for sensors with currentsinking output. (Max. sensor current = 3 mA.)Low Bias: Input trigger levels VIL = 0.25 V, V IH = 0.75 V; for increasedsensitivity when used with magnetic pickups.Hi Bias: Input trigger levels VIL = 2.5 V, VIH = 3.0 V; for logic level signals.Max. Input Signal: ±90 V; 2.75 mA max. (With both Current Sourcing andCurrent Sinking resistors switched off.)5. SIGNAL VOLTAGE OUTPUT (Selectable):0 to 5 VDC @ 10 mA max.0 to 10 VDC @ 10 mA max.6. SIGNAL CURRENT OUTPUT (Selectable):0 to 20 mA @ 10 VDC min.4 to 20 mA@ 10 VDC min.7. OUTPUT COMPLIANCE:Voltage: 10 V across a min. 1K load (10 mA). Factory calibrated for loadsgreater than 1 M.Current: 20 mA through a max. 500 load (10 VDC).8. ACCURACY: ±0.1% of full scale range (±0.2% for 0 to 5 VDC range).9. RESOLUTION:Voltage : 3.5 mV min.Current: 5 μA min.4.20 REF1.083.12(27.5)(106.7)(79.2)0987654321M1866GOUTINIFMASSTATUINSTRUCTIONS, PLEASE REFERFOR HOOK-UP AND OPERATINGINPUTCOMM85-250VAC 50/60HZ 6.5VARED LION CONTROLSMADE IN U.S.A.M1867G5FOR SET-UP INSTRUCTIONS.SEE THE IFMA BULLETINTO THE IFMA BULLETIN.!YORK, PA.OUTAC~121198V-IN6AC~60mA+12VDC107V+ 4SINKSRC.LOGICMODECFG2CFG0CFG1ONIFMAI-32I+ 1DIMENSIONS In inches (mm)CAUTION: Risk of Danger.Read complete instructions prior toinstallation and operation of the unit.CAUTION: Risk of electric shock.ORDERING INFORMATIONBulletin No. IFMA-FDrawing No. LP0340Released 07/09UL Recognized Component,File # E137808MODEL NO. DESCRIPTIONPART NUMBERS FOR AVAILABLESUPPLY VOLTAGES9 to 32 VDC 85 to 250 VACIFMA Pulse Rate to Analog Converter IFMA0035 IFMA0065For more information on Pricing, Enclosures & Panel Mount Kits refer to theRLC Catalog or contact your local RLC distributor.Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com