red lion APLSP Quick Start Manual

red lion APLSP Quick Start Manual Manual pdf 1 page image

1! 3, 4, 5, OR 6-DIGIT, 0.56" (14.2 mm) HIGH LED DISPLAY! 3, AND 5-DIGIT UNITS HAVE A “-” SIGN! FULL PARALLEL OR STROBED BCD! SELECTABLE 0 OR 1 TRUE LOGIC FOR BOTH DATA ANDSTROBE INPUTS! DIP SWITCH SELECTABLE DECIMAL POINTS! OPTIONAL ACCESSORY BOARDS FOR CASCADING! EDGE-CARD INTERFACE! SEALED FRONT PANEL CONSTRUCTION (NEMA 4/IP65)DESCRIPTIONThe Apollo Slave Display converts numerical BCD data supplied byequipment such as programmable controllers, into seven segment LED displayinformation. The Slave Display is available in 3, 4, 5 and 6 digit versions, in eithera 5 VDC or 10 to 28 VDC (3 and 5-digit versions have a “-” sign). The unit hasthree DIP Switch selectable decimal points for displaying in 10ths, 100ths and1000ths. Other DIP Switches allow selection of 0 or 1 true logic and pull-down orpull-up resistors for both the Data and Strobe inputs. The unit can display thenumbers 0-9 by sending the corresponding BCD information. Individual digitscan be blanked by sending a Binary Code greater than 9. For the 3 and 5-digitversions, the minus sign is activated by applying the selected logic true level tothe terminal marked “(-) sign” then strobing the terminal marked “(-) STR”.Four optional accessory boards provide terminal blocks for easy wire hook-up and DIP sockets to cascade the BCD lines to other units. Models ATB1 (3and 4-digit) and ATB3 (5 and 6-digit) contain all terminal block positions andare used when hooking up one Slave Display or as the first in a series ofcascaded displays. Models ATB2 (3 and 4-digit) and ATB4 (5 and 6-digit) donot have the terminal blocks for the 16 and 24 BCD data inputs. These boardsare available for use in cascaded systems where the ACA1 DIP Plug CableAssembly is used to connect the data inputs.SAFETY SUMMARYAll safety related regulations, local codes and instructions that appear in themanual or on equipment must be observed to ensure personal safety and toprevent damage to either the instrument or equipment connected to it. Ifequipment is used in a manner not specified by the manufacturer, the protectionprovided by the equipment may be impaired.SPECIFICATIONS1. POWER: Power supply must be Class 2 or SELV rated.APLSP3A, APLSP4A: 5 VDC ±20% @ 200 mA max.APLSP5A, APLSP6A: 5 VDC ±20% @ 235 mA max.APLSP3B, APLSP4B: 10 to 28 VDC @ 200 mA max.APLSP5B, APLSP6B: 10 to 28 VDC @ 235 mA max.2. INPUT IMPEDANCE (ALL Inputs): 100 KΩ3. INPUT TRIGGER LEVELS:5 V Versions: VIL = 1.0 V, V IH = 4.0 V, max. input voltage = 28 VDC10 to 28 V Version: VIL = 3.0 V, V IH = 10.0 V, max. input voltage = 28 VDC4. CERTIFICATIONS AND COMPLIANCES:SAFETYIEC 1010-1, EN 61010-1: Safety requirements for electrical equipmentfor measurement, control, and laboratory use, Part 1.IP65 Enclosure rating (Face only), IEC 529Type 4 Enclosure rating (Face only), UL50ELECTROMAGNETIC COMPATIBILITY:Refer to the EMC Installation Guidelines section of this bulletin foradditional information.5. ENVIRONMENTAL CONDITIONS:Operating Temperature: 0 to 50°CStorage Temperature: -40 to 70°COperating and Storage Humidity: 85% max. relative humidity (non-condensing) from 0°C to 50°C.Altitude: Up to 2000 meters6. CONSTRUCTION: This unit is rated for NEMA 4/IP65 indoor use.Installation Category I, Pollution Degree 27. WEIGHT: 0.9 lbs (0.41 Kg)MODEL APLSP - APOLLO SLAVE DISPLAYDIMENSIONS In inches (mm) Note: Recommended minimum clearance (behind the panel) formounting clip installation is 2.1" (53.3) H x 5.5" (140) W.PANEL CUT-OUT900 MHz ± 5 MHzImmunity to EN 50082-2Electrostatic discharge EN 61000-4-2 Level 2; 4 Kv contactLevel 3; 8 Kv airElectromagnetic RF fields EN 61000-4-3 Level 3; 10 V/m80 MHz - 1 GHzFast transients (burst) EN 61000-4-4 Level 4; 2 Kv I/OLevel 3; 2 Kv powerRF conducted interference EN 61000-4-6 Level 3; 10 V/rms150 KHz - 80 MHzENV 50204 Level 3; 10 V/mEmissions to EN 50081-2RF interference EN 55011 Enclosure class BPower mains class BCAUTION: Read complete instructionsprior to installationand operation of the unit.Bulletin No. APLSP4/6-IDrawing No. LP0114Released 1/05Simulation of cordless telephone200 Hz, 50% duty cycle