OneStart

Menu

aci MOD9200BNT User Manual

Also see for MOD9200BNT: Installation & operation instructions

Page 1 preview
Page 2 preview
Page 3 preview
Page 4 preview
Page 5 preview
Page 6 preview
Page 7 preview
Page 8 preview
Page 9 preview
Page 10 preview
Page 11 preview
Page 12 preview
Page 13 preview
Page 14 preview
Page 15 preview
Page 16 preview
Page 17 preview
Page 18 preview
Page 19 preview
Page 20 preview
Page 21 preview
Page 22 preview
Page 23 preview
Page 24 preview
Page 25 preview
Page 26 preview
Page 27 preview
Page 28 preview
Page 29 preview
Page 30 preview
Page 31 preview
Page 32 preview
Page 33 preview
Page 34 preview
Page 35 preview
Page 36 preview
Page 37 preview
Contents
  1. Table Of Contents
  2. I. Introduction
  3. II. BACnet Transceiver Installation & Network Setup
  4. b. Network Setup for Transceiver Configuration
  5. d. Manually Resetting The Factory Default IP Address
  6. III. Configuration Software
  7. d. Creating A MOD9200 Configuration File
  8. e. Input Register Configuration
  9. f. Digital Output (Coil) Register Configuration
  10. g. Analog Output (Holding) Register Configuration
  11. h. Setting the Mesh Network ID for the repeater/router devices
  12. i. Miscellaneous Menu
  13. j. Configuring The Transceiver For MSTP (RS485) Network
  14. k. Sending The Configuration File To The MOD9200
  15. l. Activating The Config File
  16. IV. Data Acquisition
  17. V. Quick Setup Instructions
  18. Pleasant View Road Middleton, Wisconsin
  19. AUTOMATION COMPONENTS, INC
aci MOD9200BNT User Manual Manual pdf 5 page image
MOD9000BNT BACnet Receiver Installation & ConfigurationAUTOMATION COMPONENTS, INC Version : 1.02305 Pleasant View Road I0000674Middleton, Wisconsin 53562 Page 5 of 37www.workaci.com (888) 967-5224II. BACnet Transceiver Installation & Network Setupa. Transceiver InstallationChoose a location close to the computer, network hub or RS485 loop.Mount the Transceiver on the wall using four #8 screws.24 VAC Input (500 mA nominal) - Connect 24VAC 60 Hz (no secondary ground) to theinput terminals using 20 AWG wire as shown in the product data sheet.Figure 1MSTP (RS485) - Use 20 gauge shielded twisted pair wire to connect the Transceiver(Terminals A+ & B-) to the network (See Figure 1).Multiple RS485 Devices - If more than one RS485 device is used the devices should be“daisy chained” or “straight-line connected” by connecting all the “A” wires to the “A”terminals and the “B” wires to the “B” terminals. Do not use spur lines or a starconfiguration24 VACInputRS485TerminalsTERM TerminationResistorHI / LO BiasResistorsConnection (J1)TCP/IPConnection (J2)Default IPJumper
/ 37
Related manuals for aci MOD9200BNT
aci MODE9200D User Manual first page preview
aci MODE9200D User Manual
aci MOD9200LON LONWORKS User Manual first page preview
aci MOD9200LON LONWORKS User Manual
aci MOD9200LON Installation And Operation Instruction Manual first page preview
aci MOD9200LON Installation And Operation Instruction Manual
aci MOD9200BNT Installation & Operation Instructions first page preview
aci MOD9200BNT Installation & Operation Instructions
This manual is suitable for:
MOD9200BNT
Product
Menu
Learn More
Menu
Legal
Menu
Copyright © 2024 OneStart. All Rights Reserved