Menu
a/d/s/ 334im Installation Manual
          | |
516warnings and tipsStudy your automobile thoroughly before you drill or cut any holes. Take extra care whenworking near gas tanks, gas lines, brake or hydraulic lines and electrical wiring.Wear eye and ear protection when using power tools.Keep the woofers and tweeters away from metal filings and shavings. Once foreign objects arestuck to the magnets or tweeter dome, it will be virtually impossible to remove them. Keep thetweeters in their protective bags until final mounting to prevent any possibility of metal dust orchips from passing through the grille and accumulating on the dome.Exercise caution when working with the 3-series with the grille removed. A slip of the hand witha screwdriver or other tool can result in irreparable damage to the cone or dome. Do not touchthe cone or dome.Do not install the components where they will be subject to excessive heat, moisture or dust; orwhere they will be kicked or repeatedly bumped or brushed.Make absolutely sure that the woofer is connected to the lowpass output and the tweeter isconnected to the highpass output of the crossover network. If these connections are reversed,low-frequency signals will be fed to the tweeter without fuse protection. In this case, the tweetermay be damaged. Such damage is not covered by the warranty.When removing or installing the grille on the 3-series, be careful not to brush the woofer’srubber surround or the tweeter’s dome with the edge of the grille. Cutting or tearing the surroundor dome will destroy the unit.Never run wires outside or beneath the vehicle where they can be snagged by road hazards orthe moving parts of the vehicle. Use existing wire channels, sills, panels and molding strips insidethe automobile to hide the wiring for neat appearance and safety.Make sure your radio/cassette/cd player and or other equipment is turned off while connectingthe 3-series speaker terminals. Turn on the various components and slowly advance the volumecontrol only after checking and double checking all connectionsNote: if sound is weak or distorted, immediately turn down the volume and see the sectionentitled troubleshooting.system planningProper system planning is the best way to maximize performance. By planning your installationcarefully you can avoid situations where the performance or reliability of your system iscompromised. Your authorized a/d/s/ dealer has been trained to know how to maximize yoursystems sonic potential. They are a valuable resource in helping you with your system designand installation.jack pinoutsspecifications334im 335im 336isfrequency response +/-3dB: 48Hz to 22kHz 48Hz to 22kHz 40Hz to 22kHzsensitivity 2.83 volt RMS pink noise measured at 1 meter: 85dB 90dB 91dBimpedance, nominal: 4 Ohms 4 Ohms 4 Ohmsrecommended amplifier power watts RMS: 15 to 100 15 to 100 15 to 150dimensions – woofer/midrange transducermounting depth (woofer): 2” / 50mm 2 3/8” / 60mm 2 7/16” / 63mmoverall height: 2 5/16” / 59mm 2 11/16” / 69mm 2 15/16” / 79mmoverall maximum diameter: 4 7/8” / 123mm 6” / 152mm 6 1/2” / 165mmmaximum height above panel without grille: 11/16” / 18mm 1/2” / 13mm 5/8” / 16mmmaximum height above panel with grille: 3/4” / 20mm 3/4” / 20mm 15/16” / 24mmmaximum grille diameter: 5 3/16” / 132mm 6 1/2” / 166mm 7 1/8” / 181mmcutout size: 4 5/8” /118mm 4 15/16” / 125mmdimensions – crossover networklength/width/height: 5 3/16” x 3 1/2” x 1 5/8” 132mm x 89mm x 42mmThiele-Small specificationsfree air resonance (Fs): 52.0Hz 57.2Hz 57.1Hzelectrical damping (Q es): .82 .34 .47mechanical damping (Qms ): 4.50 4.87 6.00total damping (Qt ): .69 .32 .44equivalent volume of compliance (V as) cubic feet / liters: 0.19 / 5.5 0.26 / 7.41 0.46 / 13.0effective cone area (S d ) in 2: 8.56 14.1 18.9center to peak linear excursion (X max): .16” / 4.0mm .16” / 4.0mm .16” / 4.0mmpeak to peak excursion: 1/2” / 12.7mm 1/2” / 12.7mm 3/4” / 19.0mmvoice coil DC resistance (R e ): 3.1 3.1 3.1voice coil diameter: 1” / 25.4mm 1” / 25.4mm 1” / 25.4mmvoice coil length (winding length): .45” / 11.5mm .45” / 11.5mm .45” / 11.5mma/d/s/ subscribes to the philosophy of continuous product development therefore the specifications may change without notice.a/d/s/ tweeters are constructed in concert with the Ferrosound program and use Ferrofluidto provide increased power handling, decreased distortion, minimum electrical impedancechange, higher linearity, and smoother frequency response. |
Related manuals for a/d/s/ 334im
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved