Zenoah BC2311LE Owner's Manual

Also see for BC2311LE: Owner's manual

Contents

Zenoah BC2311LE Owner's Manual Manual pdf 1 page image

1. Read this manual carefully until you completelyunderstand and can follow all safety notes,precautions, and operating instructions beforeusing of the unit.2. Do not operate this tool when you are tired, ill,or under the influence of alchohol, drugs, ormedication.3. Always wear eye or face protection andhearing protection.4. Do not wear loose clothing, jewelry, shorttrousers, sandals, or go barefoot. Do not wearanything which might be caught by branches ormoving part of the unit. Secure hair so it isabove shoulder length.5. Never start or run the engine inside a closedroom or building. Exhaust gases containdangerous carbon monoxide.6. Before starting the engine, inspect the entireunit for loose fasteners and fuel leakage. Makesure that the cutting attachment is properlyinstalled and securely fastened.7. Be sure the blade guard is attached in place.8. Fuel is highly flammable. Always keep openflames and sparks away from the unit and fueldepot. Do not smoke while refueling the unit ormixing fuel.9. When refueling the unit, make sure to stop theengine and allow it to cool down. Wipe spilledfuel completely from the unit. Move at least 3meters away from fueling site before startingthe engine.10. Check the condition of working area to avoidany accident by hitting hidden obstacles suchas stumps, stones, cans, or broken grass.11. Keep bystanders and animals at least 15meters away from the operating point, If youare approached, immediately stop the engine.For safe operation848JJ893A0 (709)OWNER’S MANUAL15m (50ft)(1) (2) (3) (4) (5) (6) (7)12(1) Read owner’s manual before operating this machine.(2) Wear head, eye and ear protection.(3) Wear foot protection.(4) Wear gloves.(5) Beware of thrown objects.(6) Warning / Attention(7) Keep all children, bystanders and helpers 15 meters away from the machine.Explanation of pictorialsZENOAH CO., LTD.12. Keep firm footholds and balance at all times.Do not use the unit where footing is unsteadyor slippery.13. Keep cutting attachment below waist level.14. Keep all parts of your body away from therotating cutting attachment and hot surfaces.15. Warn the operator of the danger of bladethrust. (Kick back)Blade thrust may occur when the spinningblade contacts a solid object in the criticalarea. A dangerous reaction may occur causingthe entire unit and operator to be thrustviolently. This reaction is called Kick back. As aresult, the operator can lose control of the unitwhich can cause serious or fatal injury. Kickback is more likely to occur in areas where it isdifficult to see the material to be cut.16. When inspecting or servicing the unit, makesure to stop the engine and disconnect thespark plug as necessary.17. Cover the blade when the transporting orstoring the unit. Secure the unit before forstorage or transporting to prevent loss of fuel,damage or injury.18. When replacing cutting attachment or othercomponents, be sure to use the parts suppliedor recommended by ZENOAH.19. When the unit is turned off, make sure thecutting attachment has stopped before the unitis set down.20. For units equipped with a clutch, be sure thecutting attachment stops turning when theengine idles.21. Use only for tasks explained in the instructionhandbook.22. Discard blades that are bent, warped, cracked,broken or damaged in any way.23. Instructions on stopping a coasting blade.A blade can injure while it continues to spinafter the engine is stopped or throttle control isreleased.24. Stop the engine and blade before removingmaterial that is blocking or entangling thecutting attachment.25. Use a sharp blade. A dull blade is more likelyto snag and thrust. Replace the fastening nutaccording to the manufacturer's instruction.26. Cut only material recommended by themanufacturer. Do not let the blade contactmaterial it cannot cut, such as rocks, metal etc.27. Always wear safety boots, additionally ahelmet is required if there is a risk of contactwith falling objects.Thank you for purchasing a ZENOAH product.Before using our brushcutter, please read this manual carefullyto understand the proper use of your unit.1-9 Minamidai, Kawagoe, Saitama, 350-1165 JapanBRUSHCUTTERSBC2311LEBC2611LE/WEBC3501LE/WEBC4501WEIf warning label peels off or becomes soiled andimpossible to read, you should contact the dealerfrom which you purchased the product to order newlabels and affix them in the required location(s).IMPORTANTNever modify your machine.We won’t warrant the machine, if you use theremodeled brushcutter or if you don’t observethe proper usage written in the manual.WARNING■ ENGINE[BC2311LE/BC2611LE/WE]1. Loosen the bolts temporarily attached to theclutch housing.2. Push the drivershaft toward the gearcase androtate it by hand to check that the driveshaft isengaged with the gears.3. Insert the shaft tube into the clutch housing untilit bottoms. When difficult to engage, twist theengine slightly.4. Align the positioning holes on the clutchhousing and the shaft tube and fit the bolt intothe holes. And fasten the tightning bolts byturns securely.(Tightning torque: 4.9~7.8N.m. (0.5~0.8kgm))(1) Positioning hole(2) Bolt (M5x10)(3) Tightning bolt (M5x22)3 Setup

/ 4

Related manuals for Zenoah BC2311LE