OneStart

Menu

Zaxcom RX-12RR User Manual

Also see for QRX212: User manual

Page 1 preview
Page 2 preview
Page 3 preview
Page 4 preview
Page 5 preview
Page 6 preview
Page 7 preview
Page 8 preview
Page 9 preview
Page 10 preview
Page 11 preview
Page 12 preview
Page 13 preview
Page 14 preview
Page 15 preview
Page 16 preview
Page 17 preview
Page 18 preview
Page 19 preview
Page 20 preview
Page 21 preview
Page 22 preview
Page 23 preview
Page 24 preview
Page 25 preview
Page 26 preview
Contents
  1. Table Of Contents
  2. Table Of Contents
  3. Front Panel
  4. I NSERTING THE QRX212 M ODULES
  5. H OME S CREEN E XPLAINED
  6. SYSTEM MENU
  7. RECEIVER CONFIGURE MENU
  8. CENTER FREQUENCY SET
  9. SCAN MENU
  10. FREQUENCY LIST / AUTO-PICK
  11. ENCRYPTION
  12. SETTINGS MENU
  13. Debug Bits
  14. RX-12R CONNECTOR ASSIGNMENTS
  15. DC power in (Hirose HR10A-7P 4 Pin Male)
  16. UPDATING THE RX-12R FIRMWARE
  17. How to update the firmware for the QRX212 modules
  18. PRODUCT SUPPORT
  19. ZAXCOM RX-12R SPECIFICATIONS
  20. ZAXCOM WARRANTY POLICY AND LIMITATIONS
Zaxcom RX-12RR User Manual Manual pdf 14 page image
Zaxcom RX-12R System Menu14Settings MenuAntenna PowerThe RX-12R can supply 12 volts DC voltage to power antennas. This menu setting turns on the power circuit.Please note the RX12R can supply a maximum of 50ma per antenna.LCD BrightnessThe LCD screen and key board brightness is adjustable from this menu. The brightness can be adjusted between0 and 10 with 10 being the brightest.QRX ProgramThis menu is where the QRX212 modules firmware is updated from. Upon entering the program menu the currentfirmware that each module is running will be displayed. Pressing the STAR key will initiate the update process.Please see the firmware update instructions at the back of this manual for further information on updating theQRX212 module firmware.Recall Factory DefaultsFrom within this menu pressing the star key will reset the RX-12R the factory default setting.ZaxNet Frequency ControlWhen control is enabled frequency and gain changes made on the RX-12R will be sent to the correspondingtransmitter via ZaxNet. Please note the RX-12R does not have a ZaxNet transmitter so a ZaxNet transmitter willneed to be connected to the RX-12R for the changes to be executed.Serial Port ModeSerial port mode assigns what equipment the RS422 port on the RX-12R will communicate with.When the serial port mode is set to remote the RX-12R will display data to an external PC running RX-12R remotefirmware.When the serial port mode is set to Nomad the RX-12R can send frequency and gain changes commands to thecorresponding transmitters via ZaxNet. The serial port will need to be plugged into the serial port of a Nomad 10or 12. Please note the Nomad will need to be running firmware version 7.24 or higher.This connector can also be used to connect with Oasis.AutoPick Channel SpacingThis sets the minimum spacing in MHz that will be left between frequencies when AutoPick is used. Channelspacing can be individually adjusted for ZHD 48 (300 kHz), ZHD 96 (400k Hz), and XR/Mono/Stereo transmitters(800 kHz).AutoPick BandwidthThis sets how many MHz wide AutoPick will choose the transmitter frequencies from. For example if AutoPickBandwidth is set to 10 MHz the RX-12R will only choose frequencies that are 5 MHz above and 5 MHz below thecenter frequency. AutoPick can be set from 10 to 34 MHz in 1 MHz increments.Edit NameThis sets the name of the RX-12R. The purpose of naming the RX-12R is so that if multiple RX-12R units are being usedeach unit can be identified by a name rather than the serial number.Advanced Set upBurn Boot loader
/ 26
This manual is suitable for:
QRX212RX-12RRX-12RR
Product
Menu
Learn More
Menu
Legal
Menu
Copyright © 2024 OneStart. All Rights Reserved