Yamaha RS-75 Assembling Instructions

ASSEMBLY INSTRUCTIONS◆ Cable Band (x10)◆ Assembly Instructions (this sheet)◆ Overall Assembly RS75(When the box is opened)◆ Small Screws M5 X 8(Module Holder Fixing Screws X4)■ Handling Precautions• Do not alter the product. Doing so may result in damage or deterioration to the product.• Do not step on or place heavy objects on the product. It may result in damage.• Do not use or keep the product in places with extremely high temperature (places in direct sun-light, close to a heater, in a closed car, etc.) or damp (bathroom, outside on a rainy day, etc.). Itmay result in deformation, discoloration, stickiness, damage or deterioration.• To clean the product, please wipe with a soft cloth or a damp cloth that has been wrung outthoroughly. If the product is soiled or sticky, use a neutral detergent on a cloth then wipe with adamp cloth that has been wrung out thoroughly to remove any remaining detergent. Do not usebenzine, thinner or alcohol as it may result in discoloration or deformation. Also pay close atten-tion so as not to let the water and detergent come into contact with the cushions used in theproduct, it may result in deterioration.Before using, please read this “Assembly In-struction” sheet, and use this product in a safeand proper manner.Especially for children, parents or an instructorshould teach the children the proper manner inwhich to use the device.PRECAUTIONSAlways set the instrument on a flat and solid surface. Placement on a sloping, unstable surface or on steps may result in theinstrument being unstable and overturning.Make sure all bolts are tightened firmly. Loose bolts may result in the rack overturning or parts dropping causing injury.When adjusting the height or angle, do not suddenly loosen the bolt. The pad may drop, the rack or pipes may slip, pinching orcausing injury to hands or fingers.Do not sit or step on the rack. The rack may overturn or be damaged resulting in injury.Please be careful when children are close to or touching the product. The product has many pipes and arms so carelessmovement around the product may result in injury.When setting the pads and modules, please pay close attention in regards to the handling and setting of cables. Feet maybecome entangled in the cables resulting in falls.Do not put your hands or feet under the foot pedal or foot switch. They may be pinched resulting in injury.Watch your fingers when adjusting clamps. They may become pinched resulting in injury.Be careful around pipe ends, inside the pipe and screw ends. Metal shavings, etc. may injure your fingers.Do not attach acoustic drums to the electronic drum rack. Clamps may be damaged and drums may drop, causing injury.Caution (including danger, or warning). Thismark indicates cautions in which you shouldpay close attention to.Acts indicated with this icon are prohibited andshould not be attempted.To prevent against accidents and injuryPlease follow the cautions listed below* Specifications are subject to change without notice.If this symbol is ignored and the equipment is used improperly, fatal injury to per-sons or serious damage could occur.WARNINGCAUTION If this symbol is ignored and the equipment is used improperly, there is a dangerof injury to persons handling the equipment, and material damage could occur.■ RS75 Assembly* Parts for the RS75's main structure have already been assembled before packing. After removing the unit from the box, follow the instructions described below to complete the assembly.A Phillips (+) screwdriver is required when attaching the Drum Trigger Module. Please prepare one before starting assembly.After removing the unit from the box, remove all cushion material.12 Setting up the parts• Loosen the wing bolts, slide the pipes out a little, and attach the rubber feet.• Loosen the bolts on the movable arms and legs, as shown in the diagramsbelow, then secure the bolts firmly once setting is complete.Follow the setup order (q~i) in the diagrams shown below.q weCautionLeft Leg AssemblyRight Leg AssemblyModule Holder AssemblyCautionyr tuCymbal HolderSide Arm (L) AssemblySide Arm (R) AssemblyAttaching the Drum Trigger Module33-1 Remove the module holder from the holder clamp,and use the supplied screws to attach the DrumTrigger Module.Make sure only the supplied screws areused. Using any other screws may resultin the unit falling off the holder or damage.3-2 Reattach the module holder to the holder clamp.Caution : Make sure the bolts marked with a " " are loosened before setting up.INTRODUCTIONThank you for purchasing the Yamaha Electronic Drum Rack System RS75.Before using, thoroughly read these assembly instructions, and use this productsafely and correctly.iCymbal Holder■ Inside This PackageBefore setup, please make sure that all of the items listed below are present and ac-counted for. If anything is missing, please contact the dealer from whom you purchasedthe unit.◆ Rubber Foot (x2)Rubber FootRubber FootLoosenLoosenLoosenLoosenBe careful around the pipe edges.The cut pipe ends are sharp and caninjure your fingers.

/ 2

Related manuals for Yamaha RS-75