Yamaha 520K Assembly Manual

DTX540K/DTX520K Assembly ManualThis pamphlet describes the standard procedure for DTX540K/DTX520K assembly.After assembling the parts and connecting the cords as shown below, you will be ready to turn on the drum trigger module.• For assembly, you will require four individual packages – an RS500Rack System, a DTP520C Pad Set, a DTP700P Pad Set*, and aDTX500 Drum Trigger Module. (*: The DTX520K uses a DTP520PPad Set instead.)• This pamphlet describes how to attach the pads and drum triggermodule to the RS500 Rack System. Before carrying out the proce-dures described below, ensure that you have correctly assembledthe rack system as described in its assembly manual.• Although this pamphlet uses illustrations of the DTX540K, theassembly procedures described also apply to the DTX520K.Before starting assembly, lay a drum mat (sold separately) on the floor.Alternatively, before setting up the HH65 Hi-hat Controller and KP65Kick Pad, you can place the packages' cardboard boxes on the floor toprotect it from damage.Before using, please read this assembly manual, and use this product in a safe and proper manner.* Please keep this manual in a safe place for future reference.* Make sure to read the Assembly Manual of the Rack System and the Owner’s Manual of the Pad.NOTICE• Make sure you hold onto the plug, not the cable, when connecting or disconnecting the cable. Also,never place any heavy or sharp objects on the cable. Applying excessive force to the cable mayresult in damage to the cable, such as the wires being severed, etc.• Do not step on or place heavy objects on the product. It may result in damage.• Do not use or keep the product in places with extremely high temperature (places in direct sunlight,close to a heater, in a closed car, etc.) or high humidity (bathroom, outside on a rainy day, etc.).Doing so may result in deformation, discoloration, damage or deterioration.• When cleaning the product, do not use benzine, thinner or alcohol as it may result in discoloration ordeformation. Please wipe with a soft cloth or a damp cloth that has been wrung out thoroughly. If theproduct is soiled or sticky, use a neutral detergent on a cloth then wipe with a damp cloth that hasbeen wrung out thoroughly to remove any remaining detergent. Also pay close attention so as not tolet the water and detergent come into contact with the cushions used in the product; doing so mayresult in deterioration.* Specifications and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or specifications atany time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer.ENPRECAUTIONSExample of standard DTX540K assemblyPCY100(Cymbal Pad)XP80(Tom Pad)XP70(Tom Pad)KP65(Kick Pad)XP80(Snare Pad)HH65(Hi-hat Controller)DTX500 DrumTrigger ModulePCY100(Hi-hat Pad)RS500(Rack System)PCY135(Cymbal Pad)IMPORTANTNOTICEIf this symbol is ignored and the equipment is used improperly, fatalinjury to persons or serious damage could occur.• Do not let small children assemble or set up this product by themselves, or they may be injured.Always assemble this product with adult supervision.• Be careful with the edges of the Cymbal Holders and the Tom Holders. The sharp holder endsmay result in injury.• Be careful with the edges of the spurs attached to the Kick Pad and foot pedal. The sharp endsmay result in injury.• If this product is used with a Rack System or Cymbal Stand, make sure all bolts are tightenedfirmly. Also, when adjusting the height or angle, do not suddenly loosen the bolts. Loose bolts mayresult in the rack overturning or parts dropping, causing injury.• Always set the product on a flat and solid surface. Placement on a sloping, unstable surface or onsteps may result in the product being unstable and subject to overturning.• When setting up the product, please pay close attention to the handling and setting of cables.Carelessly placed cables may cause the user and others to trip and fall.• Do not alter the product. Doing so may result in injury or damage/deterioration to the product.• Do not sit or step on the rack. The rack may overturn or be damaged, resulting in injury.If this symbol is ignored and the equipment is used improperly,there is a danger or injury to persons handling the equipment, andmaterial damage could occur.• Watch your fingers when adjusting clamps. They may become pinched, resulting in injury.• Be careful around pipe ends, inside the pipe and screw ends. Metal shavings, etc. may injure yourfingers.• Do not put your hands or feet under the foot pedal or foot switch. They may be pinched, resultingin injury.• Do not attach acoustic drums to the electronic drum rack. Clamps may be damaged and drumsmay drop, causing injury.Digital Musical Instruments DivisionDigital Musical Instruments Division©2011 Yamaha CorporationWW60810 103PO***.*01B0WARNING CAUTIONAssemble the RS500 Rack System.For details, refer to the assembly manual that came with the rack system.Check the contents of each package.Mount the pads and the drum trigger module on the rack system.As described below, mount the pads and the trigger module on the rack system, and then position the kick pad and the hi-hat controller.12Package 1: DTP520C Package 2: DTP700P (for DTX540K) PCY135Cymbal Pad (x1) PCY100Cymbal Pad (x2) HH65Hi-hat Controller (x1) Hi-hat holder (x1)  Stoppers for thePCY100 and PCY135(x3) Tuning key (x1) 9-channel snake cable (x1) PCY100, PCY135, and PCY155 Owner’s Manual (x1) HH65 Owner’s Manual (x1) Assembly Manual (this pamphlet) XP80Snare Pad (x1) XP70Tom Pad (x3) KP65Kick Pad (x1) Clamp bolts (x4) XP70 and XP80 Owner’s Manual (x1) KP65 Owner’s Manual (x1)Package 3: DTX500 DTX500 Owner’s Manual (x1) DTX500 Drum TriggerModule (x1) AC power adaptor*(x1) Module stand (x1)  Module standfastening screws (x2) Felts for thePCY135 (x1) Felts for thePCY100 (x2) Cable band (x10)Package 2: DTP520P (for DTX520K) XP80Snare Pad (x1) TP65Tom Pad (x3) KP65Kick Pad (x1) Clamp bolts (x4) XP70 and XP80 Owner’s Manual (x1) KP65 Owner’s Manual (x1) TP65, TP65S, TP100, and TP120SDOwner’s Manual (x1)* May not be included depending on your particular area.Please check with your Yamaha dealer.3Mounting the hi-hat holder1. Remove the drum trigger module clamp a from the left of the rack, together withthe left leg b.2. Assemble the holder clamp for the hi-hat holder ensuring that it is oriented asshown in the figure, and then reassemble the left leg b and the drum trigger mod-ule clamp a.Drum triggermodule clamp aLeft leg bDrum triggermodule clamp aLeft leg bHolder clampHi-hat holderContinued on other side

/ 2

Related manuals for Yamaha 520K