Menu
YASKAWA Z1000 Technical Manual
Also see for Z1000 CIMR-ZU*A Series: Programming manualProgramming manualQuick start guideTechnical manualUser manual
                                                      | |
6 Related Bypass ParametersThe following parameters are used to set up the bypass for operation with the option. Parameter setting instructions can befound in the drive manual.Confirm proper setting of the parameters in Table 4 before starting network communications. After changing parametersettings, cycle power to the bypass for the new settings to take effect.Table 4 Related ParametersNo.(Addr.Hex) Name Description ValuesF6-02(03A3) External Fault from Comm.Option Detection Selection 0: Always detected1: Detection during run only Default: 0Range: 0, 1F6-03(03A4) External Fault from Comm.Option Operation Selection0: Ramp to stop. Decelerate to stop using the deceleration time in C1-02.1: Coast to stop2: Fast Stop. Decelerate to stop using the deceleration time in C1-09.3: Alarm only <1>Default: 1Range: 0 to 3Z1-07(85CC)Speed Reference Select<2>0: Operator1: Analog Input2: Bypass Serial3: Option Board (CN5)Default: 1Range: 0 to 3Z1-08(85CD) Run Command Select <2>0: Operator1: Bypass Controller Digital Input2: Bypass Serial3: Option Board (CN5)Default: 1Range: 0 to 3Z1-38(85EB) HOA Source Select 0: Operator1: Digital Inputs2: Ser Comm & OptDefault: 0Range: 0 to 2Z1-39(85EC) Drive/Bypass Source Select 0: Operator1: Digital Inputs2: Serial CommunicationsDefault: 0Range: 0 to 2Z4-01(8700) IP Address 1 Sets the most significant octet of network static IP address. Default: 192Range: 0 to 255Z4-02(8701) IP Address 2 Sets the second most significant octet of network static IP address. Default: 168Range: 0 to 255Z4-03(8702) IP Address 3 Sets the third most significant octet of network static IP address. Default: 1Range: 0 to 255Z4-04(8703) IP Address 4 Sets the fourth most significant octet of network static IP address. Default: 20Range: 0 to 255Z4-05(8704) Subnet Mask 1 Sets the most significant octet of network static subnet mask. Default: 255Range: 0 to 255Z4-06(8705) Subnet Mask 2 Sets the second most significant octet of network static subnet mask. Default: 255Range: 0 to 255Z4-07(8706) Subnet Mask 3 Sets the third most significant octet of network static subnet mask. Default: 255Range: 0 to 255Z4-08(8707) Subnet Mask 4 Sets the fourth most significant octet of network static subnet mask. Default: 0Range: 0 to 255Z4-09(8708) Gateway IP Address 1 Sets the most significant octet of network gateway address. Default: 192Range: 0 to 255Z4-10(8709) Gateway IP Address 2 Sets the second most significant octet of network gateway address. Default: 168Range: 0 to 255Z4-11(870A) Gateway IP Address 3 Sets the third most significant octet of network gateway address. Default: 1Range: 0 to 255Z4-12(870B) Gateway IP Address 4 Sets the fourth most significant octet of network gateway address. Default: 1Range: 0 to 255Z4-13(870C) IP Address Mode Select 0: User-Defined (Static IP)1: BOOTP2: DHCPDefault: 2Range: 0 to 2Z4-14(870D) Duplex Select 0: Forced Half Duplex1: Auto Negotiate Duplex Mode and Communication Speed2: Forced Full DuplexDefault: 1Range: 0 to 2Z4-15(870E) Speed Mode Setting 10: 10 Mbps100: 100 Mbps Default: 10Range: 10, 1006 Related Bypass ParametersYASKAWA SIEPYAICOM25 Rev: A0 Z1000 Bypass Option PROFINET SI-EP3 Technical Manual 21 |
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved