YASKAWA CIMR-JU2A0012BAA Cheat Sheet

YASKAWA CIMR-JU2A0012BAA Cheat Sheet Manual pdf 1 page image

J1000 CHEAT SHEETOVERVIEWThe followingprocedure is asupplement to otherdocumentationsupplied with thisequipment and willguide the user inproperly wiring theJ1000 and motor. Itwill also allow theinstaller to checkmotor direction andcorrect if necessary.Danger: Improperwiring can and willcause bodily harmas well as damageto the equipmentWhen installing thesystem be sure tofollow good wiringpractices and allapplicable codes.Ensure that themounting of thevarious componentsare secure and thatthe environment,such as extremedampness, poorventilation etc. willnot cause systemdegradation.Please read thissheet and theQuick Start Guide(TOEPC71060626)provided with theJ1000 thoroughlybefore attemptingany installation.CHEAT SHEETTo make sure you received the correct model it is essentialto verify the J1000 nameplate with your order; and makesure that the drive has the correct rating so it can be usedwith your motor. Please check the nameplate informationas shown in the example below.· Check that the available power meets the input powerrequirements.· Ensure that the output power from the VFD iscompatible with the motor requirements.Mounting the J1000The mounting of the J1000 is extremely important regardingenvironment and accessibility. Depending on your system,there are various models available and therefore themounting dimensions (footprint) may be different. Becausethe mounting procedure is fairly extensive, it is beyond thescope of this document, the user is referred to the J1000Quick Start Guide (Manual No. TOEPC71060626) receivedwith the J1000, Section 2 Mechanical Installation. Matchup the model that you received and follow the proceduredescribed in the manual to ensure a safe and functionalinstallation. In the case where the system has more than oneJ1000 refer to the proper clearances required for adequateventilation. Please pay particular attention to:· The clearances to be maintained around the enclosurefor adequate ventilation.· The environmental specifications such as avoidingexcessive dampness, extreme temperatures, chemicalexposure, corrosive areas etc. to avoid damage to theequipment and to maintain safety.Removing Protective CoversImproper removal of the J1000 front cover and terminalcover can cause extensive damage to the J1000. To avoiddamage to these items, please pay particular attention to theJ1000 Quick Start Guide, Section 3.5, Protective Covers.· In the case of systems with multiple VFDs follow thisprocedure for each VFD and motor connected.IP20 / Open ChassisRemove the Front CoverRemove the Terminal CoverU/T1 V/T2 W/T33Ø Inductionmotor1Ø InputPowerConnectframe togroundInputProtection(Fuse or C.B.)To change direction ofmotor rotation swap anytwo of the three motorleads (See Step 2)L1 L2Fig. 1: Input Power and Output Motor ElectricalConnections for Single Phase Input J1000WARNING DO NOT CONNECT ANY OF THEFOLLOWING TERMINALS TO EARTH GROUNDSINGLE PHASEINPUT J1000(R/L1) (S/L2) (U/T1) (V/T2)Connect tochassisgroundFig.1 & 2 below show the electrical connections for theinput power and motor terminals for various J1000 DriveModels. Select the proper diagram for the single or threephase model you are installing (see Step 1) and WITHPOWER OFF make the appropriate connections.Make sure to follow good wiring practices and allapplicable codes. Ensure that the equipment isgrounded properly as shown.DANGER, LETHAL VOLTAGES ARE PRESENT- Beforeapplying power to the J1000, ensure that all protectedcovers are fastened and all wiring connections aresecure. After the power has been turned OFF, wait atleast five minutes until the charge indicatorextinguishes completely before touching any wiring,circuit boards or components.!R/L1 S/L2U/T1 V/T2 W/T33Ø Inductionmotor3Ø InputPowerConnectframe togroundInputProtection(Fuse or C.B.)To change direction ofmotor rotation swap anytwo of the three motorleads (See Step 2)L1 L2 L3Fig. 2: Input Power and Output Motor ElectricalConnections for Three Phase Input J1000(R/L1) (S/L2) (T/L3) (U/T1) (V/T2)(W/T3)Connect tochassisgroundR/L1 S/L2 T/L3B1 B2 - +1 +2(W/T3)THREE PHASEINPUT J1000Step2Step1J1000 Model Identification andMountingConnect Motor andLine PowerStep3Step4 Check Motor Direction How to Change ParametersFig. 3 Digital OperatorNext, press theUsing Safety precaution, and referring to Fig.1 or 2, swap any twoof the three output leads to the motor (U/T1, V/T2 and W/T3). Afterthe wiring change, repeat Step 3 and recheck motor direction.After the power has been turned OFF, wait at least fiveminutes until the charge indicator extinguishes completelybefore touching any wiring, circuit boards or components.DANGERIf motor rotation is not correct, then power down the J1000 Drive.should turn on.Key on the Digital Operator; the green LED!In this step the motor is checked for proper direction andoperation. This test is to be performed solely from thedigital operator. Apply power to the J1000 after all theelectrical connections have been made and protectivecovers have been re-attached. At this point, DO NOT RUNTHE MOTOR, the Digital Operator should display asshown below in Fig. 3.Next, press the key on the Digital Operator once, then pressbutton.theNext, press the key on the Digital Operator. The motorshould now be operating at low speed running in the correct forward(clockwise) direction.Next, press the key on the Digital Operator.REV LEDOFFFirst Digit FlashingFirst Digit FlashingDigital Operatorturned off.Page 1 of 2YEA Document Number: TM.J1000.01 10/15/2008 ©2008 Yaskawa Electric America, Inc. - (800) YASKAWA (927-5292) Fax (847) 887-7310 DrivesHelpDesk@yaskawa.com www.yaskawa.comThis step shows how to access and modify a J1000 parameter aswell as how to monitor J1000 signals such as output frequencyand motor current. Make sure all protective covers have been re-attached and power is turned on. DO NOT RUN THE MOTOR.Press the key once.key.The digital operator shows the parametermenu (PAr) then press theJ1000 Digital Operator power-up statePress the key to select the digityou would like to change. Next use theand keys to select theparameter group, sub-group or numberModify the parameter value using theand key and pressthe key to save the new value.Access Parameter Menu and Change Parameter ValueMonitor Motor Frequency and Motor CurrentPress the key until the FOUTLED turns on. The display now showsthe actual drive output frequency in Hz.Pressing the key again willshow the motor output current. The ‘A’behind the value means ‘Amps’.Please refer to the technical manualon how to access other drive signals.J1000 Digital Operator power-up stateMotor CurrentOutput FrequencyChange Parameter ValueSelect ParameterSelect Parameter Menu

/ 2

Related manuals for YASKAWA CIMR-JU2A0010BAA