XL Systems 0001909 Manual

XL Systems 0001909 Manual Manual pdf 1 page image

XL Systems Inc14 Dora Ln Holmdel, NJ 07733Diesel Sound Decoder with 6 Prime Mover Sound Item #0001909Thank you for purchasing our advanced DCC diesel 16 bit sound onlydecoder. Combined with any non-sound power decoder installed in yourlocomotive, and used with your favorite DCC System, our new sound onlydecoder will make your model locomotive come to life.Easy installation - two wire onlySix synchronized diesel prime movers with random associatedlocomotive sounds28 functions (F1 - F28)2 or 4-digit (1-9999) addressingProgrammable 14, 28, 128 speed stepsProgrammable acceleration rate, deceleration rateProgrammable user selectable 22 different horns and 8 bellsProgrammable individual sound volumes (16 levels)Programmable master sound volumes (16 levels)Supports advanced consisting (CV19)Supports programming on the main (OPS mode)Compatible with NMRA DCC standardsComplies with the part 15 of FCC18mm speaker includedDimensions: 17.4mm x 17.4mm x 4.0mmNote- Instead of using CV3 and CV4, the decoder uses CV120 and CV121 as accelerationand deceleration rates. So you can change its acceleration and deceleration rates withoutchanging CV3 or CV4 in your power decoder, if you already have these rates tailored foryour locomotives optimum performance.ADDRESS PROGRAMMING:The “Sounder” comes with a factory default address of #3, and 28 speed steps. If yourlocomotive has a different address, and speed step already programmed into it, place thelocomotive, with decoder and Sounder installed, on your program track and reprogram it tothe address you had originally programmed it to. While it is on the program track, alsoreprogram the locomotive to the speed step of your choice, (14-28/128). Since the decoderdoes not have a motor driver, you can’t read back its CV.ADDITIONAL INFORMATION:The Sounder synchronized diesel sound only decoder should perform well when used withother brand command systems, and decoders. See your DCC command stations manualto learn how to program and operate any decoder. For more information about register/CVs and their functions, please refer to the NMRA DCC Standard & Recommendedpractices, RP-9.2.2 available directly from the NMRA or their website at www.nmra.org.TROUBLE SHOOTING:This decoder should perform well with all DCC systems. The maximum DCC output shouldbe less than 15 V. If the locomotive does not respond to commands, it may have lost itsaddress. Please reprogram the address and program CV19 to 0 (disable consist). If itresponds slowly, you should clear its momentum by reprogramming CV120 and CV121 tozero. You should also clean the track to improve electrical pickup. Read your DCC systemmanual to learn how to program and operate the decoder. Whenever the decoder doesn’twork please use the program track to program CV# 125 with value 1 to restore the decoderto factory settings. This should bring the decoder to life with address #3.RETURN PROCEDURE:This decoder carries a 6 month warranty against factory defects. This warranty does notinclude abuse, misuse, neglect, improper installation, or any modifications made to thisdecoder. If it should become necessary to return the decoder for warranty repair/replacement, please include a copy of the original sales receipt. Please include a letter(printed clearly) with your name, address, daytime phone number, and a detaileddescription of the problem you are experiencing. Please also include a check or a moneyorder for $8.00 to cover return shipping and handling. If the decoder is no longerconsidered under warranty, then please include a check or a money order for $12.00 tocover the cost of repair or replacement and return shipping and handling.Send the decoder to:XL Systems Inc14 Dora LnHolmdel, NJ 07733Email: linzping@gmail.comFunction Idle/MovingF1 Bell on/offF2 HornF3 Air releaseF4 Coupling 1F5 Brake release / brake squealF6 Dynamic brake on/offF7 Air hose firing/uncoupling leverF8 Click 3 times will shut down when in idle/Manual notch downF9 Engine cooling fan / Manual notch upF10 Rail wheel clack (only moving)F11 Traction air compressorF12 Change prime diesel rumble type (CV123, 6 types)F13 Master volume reduce by 1 / air releaseF14 Master volume increase by 1 / air releaseF15 Air compressorF16 flange squealF17 Air releaseF18 Change bell type (8 types plus off)F19 Horn type select (total 22 different horns plus off)F20 Associated loco soundF21 Change bell volume and turn on the bellF22 Change horn volumeF23 Change diesel rumble volumeF24 Safety valve popF25 Air releaseF26 Flange noiseF27 Sand dropF28 Air releaseFUNCTION CHARTER:

/ 2

Related manuals for XL Systems 0001909