Whirlpool  UXI0600DYS Product Dimensions

Also see for UXB1200DYS: Installation instructions

600 CFM and 1200 CFM In-Line Blowers for Range HoodsPRODUCT MODEL NUMBERSLOCATION REQUIREMENTSUXI0600DY UXI1200DYBecause Whirlpool Corporation policy includes a continuous commitment to improveour products, we reserve the right to change materials and specifications without notice.Dimensions are for planning purposes only. For complete details, see InstallationInstructions packed with product. Specifications subject to change without notice.Ref. W1033101312/21/10Electrical Requirements: A 120 volt, 60 Hz, AC only, 15- or20-amp, fused electrical circuit is required.IMPORTANT: Observe all governing codes and ordinances.Have a qualified technician install the in-line blower motor system.All openings in the ceiling and wall where the in-line blower motorsystem will be installed must be sealed.For Mobile Home InstallationsThe installation of this in-line blower motor system must conform tothe Manufactured Home Construction Safety Standards, Title 24 CFR,Part 328 (formerly the Federal Standard for Mobile HomeConstruction and Safety, Title 24, HUD, Part 280) or when suchstandard is not applicable, the standard for Manufactured HomeInstallation 1982 (Manufactured Home Sites, Communities andSetups) ANSI A225.1/NFPA 501A*, or latest edition, or with localcodes.PRODUCT DIMENSIONSTop (outlet) viewBottom (inlet) view26¹⁄₈" (66.4 cm)14¹¹⁄₁₆"(37.3 cm)24³⁄₄" (62.9 cm) 14⁷⁄₈"(20.0 cm) 3³⁄₈"(8.6 cm)12¹⁵⁄₁₆"(32.9 cm)16¹⁄₈" (41.0 cm)14⁷⁄₈"(20.0 cm)3³⁄₈"(8.6 cm)VENTING REQUIREMENTS The vent system must terminate to the outdoors. Do not terminate the vent system in an attic or other enclosed area. Do not use 4" (10.2 cm) laundry-type vent or wall caps. Use round, metal vent only. Rigid metal vent is recommended. Plastic or metalfoil vent is not recommended. The length of the vent system and number of elbows should be kept to aminimum to provide efficient performance.For the most efficient and quiet operation: Use no more than three 90° elbows. Make sure there is a minimum of 24" (61.0 cm) of straight vent between theelbows if more than 1 elbow is used. Do not install 2 elbows together. Use clamps to seal all joints in the vent system. The vent system must have a damper. Use weatherproof caulking to seal the exterior wall or roof opening around thecap. The size of the vent should be uniform.Calculating Vent System LengthTo calculate the length of the system you need, add the equivalent length foreach vent piece used in the system.Vent Piece Equivalent Length45° elbow 2.5 ft(0.8 m)90° elbow 5.0 ft(1.5 m)The maximum equivalent vent lengths are:10" (25.4 cm) round vents - 60 ft (18.3 m)Example vent systemThe following example falls within the maximum recommended vent length.1 - 90° elbow = 5.0 ft (1.5 m)1 - wall cap = 0.0 ft (0.0 m)8 ft (2.4 m) straight = 8.0 ft (2.4 m)Length of system = 13.0 ft (3.9 m)90 elbow 6 ft (1.8 m)2 ft(0.6 m)Wall cap

/ 1

Related manuals for Whirlpool UXB1200DYS